Fun, Learning, Friendship and Mutual Respect
START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Blade Helicopters (eFlite) > 130X


130X Blade 130X Helicopters Information and Help


Reply
 
Thread Tools Display Modes
Old 11-30-2012, 05:55 PM   #1
Jebsmith
Registered Users
 

Join Date: Aug 2009
Location: Lexington ky
Default DS35 Servo, now heli just sits and spins

I installed the DS35 today, I made my wires too short so I just mounted the servo on the opposite side, the left side. I reversed my servo on my dx6i and the rudder functions correctly, however the heli just spins on the ground once I try and give it throttle. Any ideas?
Jebsmith is offline        Reply With Quote
Old 11-30-2012, 06:03 PM   #2
helifanatic99
 

Join Date: Nov 2012
Location: Southwest
Default

You have to mechanically reverse the servo, so figure out a way to do it like extending your wires to flip it around. You can't just reverse it electronically with the TX because there's no way to reverse the tail gyro channel. Your tail gyro is now "compensating" in exactly the wrong direction, which is nothing but spinning.
helifanatic99 is offline        Reply With Quote
Old 11-30-2012, 06:04 PM   #3
Jebsmith
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Lexington ky
Default

Jebsmith is offline        Reply With Quote
Old 11-30-2012, 06:05 PM   #4
Jebsmith
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Lexington ky
Default

Quote:
Originally Posted by helifanatic99 View Post
You are going to need to mechanically reverse the servo. You can't just reverse it electronically with the TX because there's no way to reverse the tail gyro channel. The tail gyro is now "compensating" in exactly the wrong direction, which is nothing but spinning.
So I absolutely have to swap it to the other side?
Jebsmith is offline        Reply With Quote
Old 11-30-2012, 06:07 PM   #5
gdawgs56
Registered Users
 
Posts: 2,003
 
My HF Map location
Join Date: Jan 2012
Location: Mesa, Arizona
Default

Quote:
Originally Posted by Jebsmith View Post
So I absolutely have to swap it to the other side?
yes, mount it on the right side of the boom (if looking from the rear)
gdawgs56 is offline        Reply With Quote
Old 11-30-2012, 06:08 PM   #6
Jebsmith
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Lexington ky
Default

what if I just reversed the way the tail blades responded to pitch input. All I would need to do is swap the tail grips around to the other side, then when the gyro gives them pitch they should respond correctly
Jebsmith is offline        Reply With Quote
Old 11-30-2012, 06:11 PM   #7
gdawgs56
Registered Users
 
Posts: 2,003
 
My HF Map location
Join Date: Jan 2012
Location: Mesa, Arizona
Default

yep, but then u sacrifice some pitch on the tail ... search this forum for Tail Grip Flip Mod
gdawgs56 is offline        Reply With Quote
Old 11-30-2012, 06:25 PM   #8
helifanatic99
 

Join Date: Nov 2012
Location: Southwest
Default

Quote:
Originally Posted by Jebsmith View Post
So I absolutely have to swap it to the other side?
Either that or rotate the servo arm 180 degrees to the other side. It has to be done mechanically since you cannot reverse one without the other and you cannot reverse the tail gyro's output. Unfortunately, there is no way except a firmware hack (has anyone even done it?) that a gyro channel can be reversed on the micro AS3X system, which is the FBL controller on the 130X.
helifanatic99 is offline        Reply With Quote
Old 11-30-2012, 06:27 PM   #9
helifanatic99
 

Join Date: Nov 2012
Location: Southwest
Default

Quote:
Originally Posted by Jebsmith View Post
what if I just reversed the way the tail blades responded to pitch input. All I would need to do is swap the tail grips around to the other side, then when the gyro gives them pitch they should respond correctly
You could do that and it would kinda "work". That method is still mechanically reversing the tail output (throw, not gyro) versus electronically reversing it in the TX. But, mechanically flipping the servo output at the servo is the best way to do it. That's why I like a vertical servo mount like the Microheli one. Very easy to just move the servo arm to the other side and bend the tail rotor pushrod as necessary instead of having to flip the whole servo over.
helifanatic99 is offline        Reply With Quote
Old 11-30-2012, 10:54 PM   #10
faceman425
Registered Users
 

Join Date: Oct 2011
Location: New York
Default

Jeb I did the same thing as you when I first put mine on. Just flip it around, its much easier. Take extra wire and solder it in if need be. I run my ds35 wires down through the bottom of the frame with a zip tie to hold it. Works great and the tail hold is much better with this servo.
__________________
Red Goblin 700 Vbar Blue, CY Rave ENV Nitro Vbar Silver,Trex 600LEN Vbar Silver,180CFX, 130X, JR 11X
faceman425 is online now        Reply With Quote
Old 12-01-2012, 09:16 AM   #11
Jebsmith
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Lexington ky
Default

Thanks guys, i flipped the servo to the other side, works fast now
Jebsmith is offline        Reply With Quote
Reply




Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Blade Helicopters (eFlite) > 130X


130X Blade 130X Helicopters Information and Help

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Copyright © 2004-2011 - William James - Helifreak.com