START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
BeastX FBL System BeastX FBL Flybarless System Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
02-19-2017, 04:25 PM | #1 (permalink) |
Registered Users
Join Date: Jul 2014
|
3 blade head
Hello, I have a GAUI X3L with a 3 blade head. I'm using a AR7200bx, In what position do the blades need to be in to set menu J and K. I did set menu J @ 6 degrees with the blade aligned with the fuselage and menu K @ 13 degrees with the blade 90 degrees from first set up point. The reason for asking is, when it's in the air it is real sluggish, the cyclic responds real slow. I'm using BK3001-HV servos @ 7.4 volts . I think my problem is in the set up. Has any one else had this problem ?? Thanks
__________________
70s, Nano cpx, Mcpx Bl, 130X, G-fireball , G-380, Spektrum DX8 |
Sponsored Links | |||
Advertisement |
|
02-19-2017, 08:23 PM | #2 (permalink) | |
Registered Users
Join Date: Nov 2009
|
Quote:
Link up to Studio x and hover the mouse over the control style selections and rates and expo pops up. It is easier to set it to TX mode and use the rates and expo in the TX. Might also need to up cyclic gain and pot 2 cyclic forward feed.
__________________
Align 450Pro 3GX, 500ESP/DFC 3GX, 500L, 550 DFC MicroBeast , Velocity 50 Vbar OS55 HZ-R, D380 DFC D420, G500 Sport Microbeast, All HW V4, X5 stretch 220 Flame Emax Bullet Force V2 VTX |
|
02-20-2017, 05:04 PM | #3 (permalink) | |
Registered Users
Thread Starter
Join Date: Jul 2014
|
Quote:
__________________
70s, Nano cpx, Mcpx Bl, 130X, G-fireball , G-380, Spektrum DX8 |
|
02-21-2017, 04:40 AM | #4 (permalink) |
Registered Users
|
Hello,
when Parameter menu G is set to off you're using the custom value. Here the default is '20'. This is somewhere in between the 'increased' and 'high' preset. You could try to go even higher with menu G but usually this makes the helicopter even more sluggish and inprecise as it will cause continous oversteering of you cyclic inputs. If you feel that the response is somewhat slow and delayed in general, better turn up the Direct gain (Dial 2) and do not use so high values at menu G. In contrast to increasing dial 2 you could additionaly turn down the swash gain (dial 1) a little bit which will lessen the flybarless control und put away the "robotic feel".
__________________
best regards from Germany Stefan BEASTX r&d Team freakware.com |
02-21-2017, 06:14 AM | #5 (permalink) | |
Registered Users
Join Date: Nov 2009
|
Quote:
Ya I upped pot 2 on all of mine after setting the gain Did you max out you limits, L when setup? If you got the Blue led early during the cyclic 6 deg setup maybe move the balls out the horn to speed up your input? It would have to come on around early 5s. Head speed high enough?
__________________
Align 450Pro 3GX, 500ESP/DFC 3GX, 500L, 550 DFC MicroBeast , Velocity 50 Vbar OS55 HZ-R, D380 DFC D420, G500 Sport Microbeast, All HW V4, X5 stretch 220 Flame Emax Bullet Force V2 VTX |
|
02-21-2017, 09:54 PM | #6 (permalink) |
Registered Users
Join Date: Jan 2012
|
Although I don't use D/R myself (I use servo travel adjustments on mine instead) I'm surprised that with your D/R up to 125 it isn't sufficiently quick enough.
What radio are you using? I can tell you wholeheartedly that on my DX8 with D/R at 100 and servo travels on aileron and elevator turned up to 122 that my 7200 flies *significantly* faster than it does at 100. I've played around with other settings, but that is the one consistent setting that will wake up a 7200 (or BX) in a way that has suited me. Worth a shot if you haven't tried it; I'd put D/R back to 100 and then start upping the servo travel. Once you get it above 110 or so it will come alive. Also, as bad007 mentioned, what headspeed are you running? Sent from my XT1096 using Tapatalk |
02-22-2017, 09:26 PM | #7 (permalink) | |
Registered Users
Join Date: Nov 2009
|
Quote:
__________________
Align 450Pro 3GX, 500ESP/DFC 3GX, 500L, 550 DFC MicroBeast , Velocity 50 Vbar OS55 HZ-R, D380 DFC D420, G500 Sport Microbeast, All HW V4, X5 stretch 220 Flame Emax Bullet Force V2 VTX |
|
02-22-2017, 09:32 PM | #8 (permalink) |
Registered Users
Join Date: Jan 2012
|
Understood. IMHO, the default settings on a BX are too slow for my liking, luckily with a little tweaking it can be tuned to sing. I'm curious to see what the OP comes up with
__________________
180CFX, Trex 550E (night), Goblin 570, Goblin 630C, DX8 |
02-23-2017, 06:21 PM | #9 (permalink) |
Registered Users
Thread Starter
Join Date: Jul 2014
|
Snap /Crackle / Pop, I got it. I'm using a Dx8 , Head speed is ? I have a 11 tooth main motor gear with the stock main gear @130 tooth. I did reset menu J @ 6 degrees with the blades aligned with the fuselage and menu K @ 13 degrees with the blades apx. 120 degrees from first set up point. I adj. pod two on the AR7200bx up 1/4 turn, and adj. pod one 1/4 turn down. In parameter menu B (control behavior) I went back to transmitter, and in parameter menu G I have it off. The D/R is back @ 100 and the expo is @ 0 . After flying it with these settings it was much faster but I wanted more, so I set the travel on the aileron, elevator @130 and now it is so fast it feels like it wants to rip the head off !!!! I am going in the right direction, so with a little more tuning I should be able to get it to feel like my two blade helis. Thanks for all the segg. With out you guys my GAUI X3L would still be flying like a drunken elephant. Thanks Pat
__________________
70s, Nano cpx, Mcpx Bl, 130X, G-fireball , G-380, Spektrum DX8 |
02-23-2017, 07:10 PM | #10 (permalink) |
Registered Users
Join Date: Nov 2009
|
Great Yep any defaults in the control behavior are dumbed down bad. Got my first BX and didn't know what to expect and read so many times to set up for sport. Crap, no cyclic or rudder response and took to HF and BX support jumped in and 2 flights latter shazam
__________________
Align 450Pro 3GX, 500ESP/DFC 3GX, 500L, 550 DFC MicroBeast , Velocity 50 Vbar OS55 HZ-R, D380 DFC D420, G500 Sport Microbeast, All HW V4, X5 stretch 220 Flame Emax Bullet Force V2 VTX |
Thread Tools | |
Display Modes | |
|
|