Register Now

megraham · 11-15-2013, 08:20 PM

Followed the videos and setup the DX6i just as the video showed. Went to bind and had to try a few times and finally it worked but couldn't get the motors to start. Also had a continuous beep in smart mode but when I changed it to stability the beeping stopped. It would also stop in smart mode when I raised or lowered the trim of the right stick. Once I adjusted the trim, I tried starting the motors again but nothing happened.

Any suggestions or tips to get this thing bound?

755 robert · 11-15-2013, 08:35 PM

Try trimming the throttle channel up a few clicks at a time till you get an arming tone...

megraham · 11-15-2013, 08:42 PM

Tried increasing it 1 click at a time but this didn't work in my case.

hotrodhawk · 11-15-2013, 08:56 PM

I had this problem when I had DR high rate 100% assigned to the (1) position on switches. It needs to be on the (0) side of each switch and 70% on the (1) side on a dx6. Wish they would of called that out clearly in set up config.

Have alie and elv dr in the (0) position to arm motors with the throttle trim 3 clicks above center.

PaPaGrizz · 11-16-2013, 01:37 PM

Instead of messing with the throttle trim on my Dx6i, I went into the program menu and selected "sub trim" > throttle, and set it to =10% if that doesn't work you can keep adjusting the percentage up..

Hope that helps.

11-15-2013, 08:20 PM	#1 (permalink)
megraham Registered Users Join Date: Oct 2013	Binding the DX6i with the 350 QX Followed the videos and setup the DX6i just as the video showed. Went to bind and had to try a few times and finally it worked but couldn't get the motors to start. Also had a continuous beep in smart mode but when I changed it to stability the beeping stopped. It would also stop in smart mode when I raised or lowered the trim of the right stick. Once I adjusted the trim, I tried starting the motors again but nothing happened. Any suggestions or tips to get this thing bound?

11-15-2013, 08:35 PM	#2 (permalink)
755 robert Registered Users Join Date: Feb 2010	Try trimming the throttle channel up a few clicks at a time till you get an arming tone... __________________ 700 class nitro,2X 600class electric,2X 450class,250 class,130 class,a few mcpx class().Dx-7.All helis fbl...If I had a dollar for every dollar I've spent on heli's ...I would break even. .Who is John Galt?

11-16-2013, 01:37 PM	#5 (permalink)
PaPaGrizz Registered Users Join Date: Oct 2013	Instead of messing with the throttle trim on my Dx6i, I went into the program menu and selected "sub trim" > throttle, and set it to =10% if that doesn't work you can keep adjusting the percentage up.. Hope that helps. __________________ Blade cx, 2 x 107g's, wl 202, Frankenquad, wl 212, wl 222, syma x1, blade 350qx Dx6i, rc logger eye one xtreme, Nano Qx, 200 srx, Mcx2 for indoor grins The only easy day was yesterday!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-15-2013, 08:42 PM	#3 (permalink)
megraham Registered Users Thread Starter Join Date: Oct 2013	Tried increasing it 1 click at a time but this didn't work in my case.

11-15-2013, 08:56 PM	#4 (permalink)
hotrodhawk Registered Users Join Date: Jul 2012	I had this problem when I had DR high rate 100% assigned to the (1) position on switches. It needs to be on the (0) side of each switch and 70% on the (1) side on a dx6. Wish they would of called that out clearly in set up config. Have alie and elv dr in the (0) position to arm motors with the throttle trim 3 clicks above center.

Register Now

Log-in