Register Now

helobob · 10-07-2011, 07:54 PM

Sorry repeat post from other thread, should have been here in the first place. Anyway, I got my DX8 back from gimbal recall and while playing around with it on the sim, I noticed in the Monitor screen -12 aileron and in the D/R Expo screen -13 > -13. I checked servo setup and have 0 sub trim, also checked trim button and its zeroed on chirp sound. Does this sound normal ?

or does it go back to HH again!

oh yea the D/R is 100 100. and center line is left of center in D/R expo display.

aerocal · 10-07-2011, 10:05 PM

Do a full calibration of the sticks and knob.

helobob · 10-08-2011, 07:24 PM

Not sure about knob, but I did the stick calibration as shown in the manual and still end up the same.

aerocal · 10-08-2011, 09:55 PM

Bob

See my post in this thread

https://www.helifreak.com/showthread.php?t=343999

helobob · 10-12-2011, 05:58 PM

Aerocal, Thanks!
Idownloaded the update, did the calibration ( I also needed to center the trim buttons on each model)..... I now have perfect centering!

aerocal · 10-13-2011, 12:53 PM

10-07-2011, 07:54 PM	#1 (permalink)
helobob Join Date: Jan 2011	DX8 Aileron not centering correctly Sorry repeat post from other thread, should have been here in the first place. Anyway, I got my DX8 back from gimbal recall and while playing around with it on the sim, I noticed in the Monitor screen -12 aileron and in the D/R Expo screen -13 > -13. I checked servo setup and have 0 sub trim, also checked trim button and its zeroed on chirp sound. Does this sound normal ? or does it go back to HH again! oh yea the D/R is 100 100. and center line is left of center in D/R expo display.

10-07-2011, 10:05 PM	#2 (permalink)
aerocal Registered Users Join Date: Jun 2008	Do a full calibration of the sticks and knob. __________________ Too many helis & Too many planks Lots of DX radios & A couple Futaba 72mhz radios AMA member & Full scale plank driver HELIFREAK !!!

10-08-2011, 09:55 PM	#4 (permalink)
aerocal Registered Users Join Date: Jun 2008	Bob See my post in this thread https://www.helifreak.com/showthread.php?t=343999 __________________ Too many helis & Too many planks Lots of DX radios & A couple Futaba 72mhz radios AMA member & Full scale plank driver HELIFREAK !!!

10-13-2011, 12:53 PM	#6 (permalink)
aerocal Registered Users Join Date: Jun 2008	__________________ Too many helis & Too many planks Lots of DX radios & A couple Futaba 72mhz radios AMA member & Full scale plank driver HELIFREAK !!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-08-2011, 07:24 PM	#3 (permalink)
helobob Thread Starter Join Date: Jan 2011	Not sure about knob, but I did the stick calibration as shown in the manual and still end up the same.

10-12-2011, 05:58 PM	#5 (permalink)
helobob Thread Starter Join Date: Jan 2011	Aerocal, Thanks! Idownloaded the update, did the calibration ( I also needed to center the trim buttons on each model)..... I now have perfect centering!

Register Now

Log-in