START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Align 3G FBL System Align 3G FBL Flybarless System Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
03-17-2010, 07:19 PM | #1 (permalink) |
Registered Users
Join Date: Jul 2009
|
Need help on setup 3g trex 600 with ar7100r
Ok i am so confused right now..lol I have built the kit and now am on the servo setup.I know that i need to get everything 90 on the arms following the directions for all the link lengths.Here is what i got AR7100r reciever,align servos,align 3g setup,9303 radio.Im not sure where to plug all the wires into. pics,diagrams hell come over and help..lol I am just baffled right now. I think the reciever is confusing me that it has a regulated and non regulated ports
__________________
"You never know how strong you are until being strong is the only choice you have" |
Sponsored Links | |||
Advertisement |
|
03-17-2010, 08:32 PM | #2 (permalink) |
Registered Users
Join Date: Apr 2008
|
cyclic servos go pluigged in to the 3g unit. Servo signal and power wires from 3g will b labeled . plug these into the unregulated portion of the rec. Tail servo goes into the 3g cu. rudder and gain wires go pkugged into the rec. on the regulated portion. Throttle servo, regulated portion. DO NOT use the "gear" output for anything except for maybe a sig. for a switch glo. use aux 2 for gyro gain. Set up radio in menu accordingly.
I know this sounds sparse but if ya let me know as u get to certain steps, ill help ya get through it. |
03-18-2010, 03:31 AM | #3 (permalink) | |
Registered Users
Thread Starter
Join Date: Jul 2009
|
Quote:
__________________
"You never know how strong you are until being strong is the only choice you have" |
|
03-18-2010, 05:32 AM | #4 (permalink) |
Registered Users
Join Date: Apr 2009
|
You have exactly the same set-up as I do, Switchglow and everything. I love that switch glow!!! I will take pics tonight and run through the settings if you wish!
|
03-18-2010, 07:21 AM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Jul 2009
|
Radio too?yes that would be Sweet that will get me in the air quick I'll be on tonight thanks you guy rock
__________________
"You never know how strong you are until being strong is the only choice you have" |
03-18-2010, 05:14 PM | #6 (permalink) |
Registered Users
Join Date: Apr 2008
|
Camera took a dirt nap. itll get replaced by the evening on fri.
|
03-19-2010, 05:45 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Jul 2009
|
just checking back to see if you guys have those pics
__________________
"You never know how strong you are until being strong is the only choice you have" |
03-19-2010, 07:07 PM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Jul 2009
|
__________________
"You never know how strong you are until being strong is the only choice you have" |
03-19-2010, 07:53 PM | #9 (permalink) |
Registered Users
Join Date: Apr 2009
|
Here is a pic for the 7100r switch glo and 3g in a 600
Switch glow on the Top, unregulated portion of rec. Then Aileron Right forward servo Then Elev. Aft servo Then skip Gear Then Left forward servo Pitch Then Throttle servo skip gear Then Rudder servo Then rudder sensitivity Engine sensor center back of 7100r |
08-08-2010, 01:15 AM | #10 (permalink) | |
Registered Users
Join Date: Jun 2009
|
Quote:
hi how are you?i was looking at a comment you have made on a post about a AR7100 RX you have said NOT to use the gain channel for the gain on the gyro but you didnt say why i was just trying to find out why you cant use it?any help on this would be great thanks very much nick |
|
08-08-2010, 01:31 AM | #11 (permalink) |
Registered Users
Join Date: Jun 2009
|
any help would be great i have one i need to set up
nick |
08-10-2010, 01:54 AM | #12 (permalink) |
Registered Users
Join Date: Mar 2008
|
Also curious about the gear channel comment. Are you using an x9303 Jondabear?
__________________
700N LE - 3G, 91HZ-R, SB-20FH-2, AR7100R, Edge 693FBL 600NSP - 3G, 55HZ, B320, 8717, 8900G, AR7100, Edge 603FBL 450 Pro & 450 SEv2 Stock Setups 450 SEv2 - SK360, MiniG, HKII-2221-6, CC 60, Edge 325FBL 250 SE - GY520, 290G & 250 Orig Stock Setup ---- JR 12x/Spek DX7se |
08-10-2010, 05:46 AM | #13 (permalink) |
Registered Users
|
The gear channel on the AR7100R is used internally for Governor/Limiter speed adjustment.
Page 15 >
__________________
T-rex 700n VBar 5.3 Pro | T-rex 700e V3 VBar 5.3 Pro | JR DSX9 Limited Team RCBits | Team Lynx |
08-10-2010, 02:22 PM | #14 (permalink) |
Registered Users
Join Date: Mar 2008
|
Ahh I should have remembered that from setting mine up but it's been a while. Ty for the answer.
__________________
700N LE - 3G, 91HZ-R, SB-20FH-2, AR7100R, Edge 693FBL 600NSP - 3G, 55HZ, B320, 8717, 8900G, AR7100, Edge 603FBL 450 Pro & 450 SEv2 Stock Setups 450 SEv2 - SK360, MiniG, HKII-2221-6, CC 60, Edge 325FBL 250 SE - GY520, 290G & 250 Orig Stock Setup ---- JR 12x/Spek DX7se |
Thread Tools | |
Display Modes | |
|
|