Register Now

mhoebrec · 02-25-2012, 10:47 AM

I am installing a HC3-SX and I have a Jive 80+ LV ESC on a TREX-550 helicopter. If I use a slave cable on the JIVE that I connect to the battery port of a HC3-SX, the ESC doesn't arm. The led is not flashing, I only hear a faint sound that resembles tac, tac, tac, tac, ... When I remove the slave cable, the Jive arms immediately.

I already removed the orange wire from the slave cable.

What could be wrong?

heli21 · 02-25-2012, 12:01 PM

I did not remove any wires from my slave cable, I simply plugged the signal wire from the Jive into the throttle/esc channel on the HC and the slave cable into head servo 4/battery port on the HC, works like a charm every time

Rob
Helicommand Flight Team

mhoebrec · 02-25-2012, 03:04 PM

Quote:

Originally Posted by heli21

I did not remove any wires from my slave cable, I simply plugged the signal wire from the Jive into the throttle/esc channel on the HC and the slave cable into head servo 4/battery port on the HC, works like a charm every time

Rob
Helicommand Flight Team

Thanks Rob.

That's exactly what I tried, but the Jive doesn't like it in my case.

I don't know if it is related, but I am using an sbus receiver.

drfrankencopter · 03-13-2012, 09:34 AM

Was this issue successfully resolved?

Where do you plug the master cable?

Cheers

Kris

DEMONjoe · 03-13-2012, 11:46 AM

I also do have no idea, as the power is simply running through inside the HC. All servo ports as well as ESC output, RX input and PC port are in one line. So the only thing I can think of is that there is some defect in the ESC/BEC cable?!

But yes, as there is some time over since, it would be interesting to know: did you solve it and what was it?

Thanks,
Joachim

mhoebrec · 03-13-2012, 12:12 PM

It still doesn't work with the slave cable. This weekend I had to reset the Jive and configure it again because the led blinked 8 times and the motor didn't spool up properly. This is perhaps related to the issues with the slave cable, but I have not yet tried to connect the slave cable since. This will be something to try over the weekend.

I did check the cable, but I couldn't find find anything wrong with it.

Kris, you connect the master cable to the third slot of the HC3 (throttle output) when using an sbus receiver.

02-25-2012, 10:47 AM	#1 (permalink)
mhoebrec Registered Users Join Date: May 2009	Slave cable of a Jive 80+ LV to a HC3-SX I am installing a HC3-SX and I have a Jive 80+ LV ESC on a TREX-550 helicopter. If I use a slave cable on the JIVE that I connect to the battery port of a HC3-SX, the ESC doesn't arm. The led is not flashing, I only hear a faint sound that resembles tac, tac, tac, tac, ... When I remove the slave cable, the Jive arms immediately. I already removed the orange wire from the slave cable. What could be wrong?

03-13-2012, 11:46 AM	#5 (permalink)
DEMONjoe Registered Users Join Date: Dec 2010	I also do have no idea, as the power is simply running through inside the HC. All servo ports as well as ESC output, RX input and PC port are in one line. So the only thing I can think of is that there is some defect in the ESC/BEC cable?! But yes, as there is some time over since, it would be interesting to know: did you solve it and what was it? Thanks, Joachim __________________ Joachim CAPTRON Electronic GmbH - bavarianDEMON Support, Product & Sales Manager -

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-25-2012, 12:01 PM	#2 (permalink)
heli21 My HF Map location Join Date: Jun 2008	I did not remove any wires from my slave cable, I simply plugged the signal wire from the Jive into the throttle/esc channel on the HC and the slave cable into head servo 4/battery port on the HC, works like a charm every time Rob Helicommand Flight Team

03-13-2012, 09:34 AM	#4 (permalink)
drfrankencopter Registered Users Join Date: Feb 2011	Was this issue successfully resolved? Where do you plug the master cable? Cheers Kris

03-13-2012, 12:12 PM	#6 (permalink)
mhoebrec Registered Users Thread Starter Join Date: May 2009	It still doesn't work with the slave cable. This weekend I had to reset the Jive and configure it again because the led blinked 8 times and the motor didn't spool up properly. This is perhaps related to the issues with the slave cable, but I have not yet tried to connect the slave cable since. This will be something to try over the weekend. I did check the cable, but I couldn't find find anything wrong with it. Kris, you connect the master cable to the third slot of the HC3 (throttle output) when using an sbus receiver.

Register Now

Log-in