Register Now

qb7ops · 02-21-2007, 12:20 PM

Hi all,

I have a Logo 10 Carbon Fiber frame set and would like to pick up a pair of battery plate supports for it. I have seen the supports on many L10's here. Could someone please confirm that the Mikado Part #M2007 will actually fit on the L10 CF? http://www.fxaeromodels.com/product_...f46662100102e4.

I want to make sure the supports will "actually" fit because the last time I purchased a part that said it was for a Logo 10, it turned out not to fit the Logo 10 CF, but did not state that.

Thanks in advance!

MicroMan · 02-21-2007, 12:42 PM

I know it'll fit on the plastic frame, you may want tp give fxaeromodels a call and confirm it'll fit on your CF Logo 10.

qb7ops · 02-21-2007, 01:13 PM

I did send FX and email, but I am sure someone on helifreak will know. (At least I hope so)

Chachin · 02-22-2007, 10:48 AM

Hello,

It probably won't be a direct fit. You will have to drill a couple of attachment holes at the low and fwd end of the CF frame for it to align properly and support the underside of the long battery plate.

Haven't tried it myself though. Here's how an E-Zone member did his longer version batt. cradle in his Carbon Logo10:

http://www.rcgroups.com/forums/showp...9&postcount=10

Chachin..

02-22-2007, 06:27 PM

I went to install one on my CF 10 and it was going to take some work so instead i added plateoff the botom of the motor mount i extended it about 2 inches out and holds my 6s1p 3700 evo flawless

Bobby

ozace · 02-23-2007, 10:56 PM

Thanks for the link Chachin, i missed this post

02-23-2007, 11:09 PM

Nice work Ozace!

Bobby

qb7ops · 02-24-2007, 05:07 AM

It looks like the one Ozace attached is the M4000 and not the M4007. The M4000 looks longer in the picture and might be easier to adapt than the shorter looking M4007. I hope I am correct on this. Will give it ago just the same.

M4007 http://www.fxaeromodels.com/product_...50492ada1bdc76

M4000 http://www.fxaeromodels.com/product_...50492ada1bdc76

ozace · 02-24-2007, 03:42 PM

The reason i used the longer one, is the logo i have it intstalled on has the 550 stretch kit and i needed the packs as far forward as possible to balance. The smaller mount attaches the same way (i have it on my other logo10)

qb7ops · 02-24-2007, 11:51 PM

So either one....good stuff Ozace. I will go with the shorter ones until I have the need to stretch. Thanks againf for you input.

02-21-2007, 12:20 PM	#1 (permalink)
qb7ops Join Date: Aug 2006	Carbon Battery Support For Logo 10 "CF" Hi all, I have a Logo 10 Carbon Fiber frame set and would like to pick up a pair of battery plate supports for it. I have seen the supports on many L10's here. Could someone please confirm that the Mikado Part #M2007 will actually fit on the L10 CF? http://www.fxaeromodels.com/product_...f46662100102e4. I want to make sure the supports will "actually" fit because the last time I purchased a part that said it was for a Logo 10, it turned out not to fit the Logo 10 CF, but did not state that. Thanks in advance!

02-21-2007, 12:42 PM	#2 (permalink)
MicroMan Registered Users Join Date: Sep 2006	I know it'll fit on the plastic frame, you may want tp give fxaeromodels a call and confirm it'll fit on your CF Logo 10. __________________ OSCAR WILDE: A little sincerity is a dangerous thing, and a great deal of it is absolutely fatal. \| Gaui Hurricane 550 \| Gaui 200 v2 SE \| Phoenix Sim \| Team ACME \|

02-22-2007, 10:48 AM	#4 (permalink)
Chachin Registered Users Join Date: Apr 2005	Hello, It probably won't be a direct fit. You will have to drill a couple of attachment holes at the low and fwd end of the CF frame for it to align properly and support the underside of the long battery plate. Haven't tried it myself though. Here's how an E-Zone member did his longer version batt. cradle in his Carbon Logo10: http://www.rcgroups.com/forums/showp...9&postcount=10 Chachin.. __________________ * Powered by ThunderPower * You'll never experience true freedom until you are living debt-free! (DaveRamsey.com)

02-23-2007, 10:56 PM	#6 (permalink)
ozace Registered Users Join Date: May 2006	Thanks for the link Chachin, i missed this post __________________ more than enough now

02-24-2007, 03:42 PM	#9 (permalink)
ozace Registered Users Join Date: May 2006	The reason i used the longer one, is the logo i have it intstalled on has the 550 stretch kit and i needed the packs as far forward as possible to balance. The smaller mount attaches the same way (i have it on my other logo10) __________________ more than enough now

02-21-2007, 01:13 PM	#3 (permalink)
qb7ops Thread Starter Join Date: Aug 2006	I did send FX and email, but I am sure someone on helifreak will know. (At least I hope so)

02-22-2007, 06:27 PM	#5 (permalink)
BobbySmith	I went to install one on my CF 10 and it was going to take some work so instead i added plateoff the botom of the motor mount i extended it about 2 inches out and holds my 6s1p 3700 evo flawless Bobby

02-23-2007, 11:09 PM	#7 (permalink)
BobbySmith	Nice work Ozace! Bobby

02-24-2007, 05:07 AM	#8 (permalink)
qb7ops Thread Starter Join Date: Aug 2006	It looks like the one Ozace attached is the M4000 and not the M4007. The M4000 looks longer in the picture and might be easier to adapt than the shorter looking M4007. I hope I am correct on this. Will give it ago just the same. M4007 http://www.fxaeromodels.com/product_...50492ada1bdc76 M4000 http://www.fxaeromodels.com/product_...50492ada1bdc76

02-24-2007, 11:51 PM	#10 (permalink)
qb7ops Thread Starter Join Date: Aug 2006	So either one....good stuff Ozace. I will go with the shorter ones until I have the need to stretch. Thanks againf for you input.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in