Register Now

DannoHk450 · 03-13-2012, 11:19 PM

I had an hk450 se v2 but crashed it in a hover from about 4' off the ground..lots of bent parts and my left aieleron servo was making a huge humming noise like it had been damaged some how....anyway i purchased many replacement parts as well as a new hk450gt....got the new one put all together with new servos and stuff...only parts from previous build were the rx,motor and esc.... When i plugged thhe new heli in to adjust my servos to center the left servo did the same thing that my previous heli was doing. Does this mean that my rx was damaged as well or would it be the.esc??? Is it possible that only ch6 rx port was damaged?? Im a bit confused on what could be the problem.. i plan to buy a couple more rx's...if i do that i can just bind them with my tx correct??? Advice,suggestions or similar problems welcome.... Thank you.

wanderer56 · 03-14-2012, 10:47 AM

Try swapping out the servo leads on the rx. If the other servo does the same thing, it's probably the rx or a setting in your tx.

Did you replace all the cyclic servos? esc wouldn't cause a problem with servo's unless it was shorted out or something. You can unplug the esc and see if the servo's behave correctly.

What tx and rx are you using? Depends on the combination of rx/tx as to weather or not you can bind one to another. Usually it's brand specific, but there are fbl systems that will bind to different tx's.

DannoHk450 · 03-14-2012, 05:00 PM

I currently have the HKT6A v2 tx and rx..Kinda got it before I had any idea about the programming aspect but it works pretty well with the exception of having to use a computer to program stuff into it.. My next purchase will be a better quality tx and rx that can hold different configs and stuff. That will be when I can fly these things a little bit better...For now Im sticking with cheap stuff .
Im pretty sure I can just buy the HK receivers and bind them with my Tx. I ordered 2 more but they are on backorder. I will try your suggestions and see what happens. All brand new servos so its probably a problem with the rx..Thinking about pullin it apart and see if a solder came loose or something
I dont think its the transmitter. The only thing i changed in there were the subtrims back to zero before leveling the servo horns. If it is I guess the only thing to do would be to clear everything out and start completely over with Tx settings because I have no Idea what might have been changed.
I will let you know how it turns out. Thanks for helping.

wanderer56 · 03-14-2012, 05:52 PM

Fun, Learning, Friendship and Mutual Respect

03-13-2012, 11:19 PM	#1 (permalink)
DannoHk450 Registered Users Join Date: Jan 2012	please help I had an hk450 se v2 but crashed it in a hover from about 4' off the ground..lots of bent parts and my left aieleron servo was making a huge humming noise like it had been damaged some how....anyway i purchased many replacement parts as well as a new hk450gt....got the new one put all together with new servos and stuff...only parts from previous build were the rx,motor and esc.... When i plugged thhe new heli in to adjust my servos to center the left servo did the same thing that my previous heli was doing. Does this mean that my rx was damaged as well or would it be the.esc??? Is it possible that only ch6 rx port was damaged?? Im a bit confused on what could be the problem.. i plan to buy a couple more rx's...if i do that i can just bind them with my tx correct??? Advice,suggestions or similar problems welcome.... Thank you.

03-14-2012, 10:47 AM	#2 (permalink)
wanderer56 Registered Users My HF Map location Join Date: Oct 2009	Try swapping out the servo leads on the rx. If the other servo does the same thing, it's probably the rx or a setting in your tx. Did you replace all the cyclic servos? esc wouldn't cause a problem with servo's unless it was shorted out or something. You can unplug the esc and see if the servo's behave correctly. What tx and rx are you using? Depends on the combination of rx/tx as to weather or not you can bind one to another. Usually it's brand specific, but there are fbl systems that will bind to different tx's. __________________ Trex 500-3226-1600, 14T, Koby 90LV, HS-5245MG, DS655, AR7200BX, DFC Trex 450 Sport-2221-8, 15T, CC Edge 50 Lite, HS-5065MG, HSG-5084MG, AR7200BX, DFC DX8

03-14-2012, 05:52 PM	#4 (permalink)
wanderer56 Registered Users My HF Map location Join Date: Oct 2009	Fun, Learning, Friendship and Mutual Respect __________________ Trex 500-3226-1600, 14T, Koby 90LV, HS-5245MG, DS655, AR7200BX, DFC Trex 450 Sport-2221-8, 15T, CC Edge 50 Lite, HS-5065MG, HSG-5084MG, AR7200BX, DFC DX8

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-14-2012, 05:00 PM	#3 (permalink)
DannoHk450 Registered Users Thread Starter Join Date: Jan 2012	I currently have the HKT6A v2 tx and rx..Kinda got it before I had any idea about the programming aspect but it works pretty well with the exception of having to use a computer to program stuff into it.. My next purchase will be a better quality tx and rx that can hold different configs and stuff. That will be when I can fly these things a little bit better...For now Im sticking with cheap stuff . Im pretty sure I can just buy the HK receivers and bind them with my Tx. I ordered 2 more but they are on backorder. I will try your suggestions and see what happens. All brand new servos so its probably a problem with the rx..Thinking about pullin it apart and see if a solder came loose or something I dont think its the transmitter. The only thing i changed in there were the subtrims back to zero before leveling the servo horns. If it is I guess the only thing to do would be to clear everything out and start completely over with Tx settings because I have no Idea what might have been changed. I will let you know how it turns out. Thanks for helping.

Register Now

Log-in