START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
06-09-2012, 10:31 PM | #1 (permalink) |
Registered Users
Join Date: Sep 2010
|
hobbywing digital phase sensor
ok I hooked it up to my 700 and I get know rpm reading from it on the main scrren where it shows requested and current, it shows no current rpm ive checked 2 different sensors and still no rpm where did i go wrong checked all the wires and have good connection
__________________
RCHN Citizen 790 -Protos maxv2 evo,xnova,Hw160, xpert, brain-Logo 600sxv2, hw130, mks scorpion,optipower,brainProtos -380 evo,Mks,xnova,HW,pulse,brain2. Jeti ds16 |
Sponsored Links | |||
Advertisement |
|
06-10-2012, 08:28 PM | #2 (permalink) |
Registered Users
Join Date: Jan 2011
|
what is your setup
log? vbar setup file? ect more info is needed for anyone to help you what procedures did you follow in setting the gov up ect ect
__________________
Vcontrol-Vbar-Nitro Gov Whip Nitro 105 Awaiting V2 Conversion Synergy N7 105 *Perspective is key* |
06-11-2012, 12:33 PM | #3 (permalink) |
HF Support
|
If you're running a receiver pack, do you have the pack ground and the ESC ground connected together?
__________________
Alan (just call me "Bum"; no need to be so formal) HeliFreak Support Protos Max Evo 700 (Brain 2), Protos Max V2 770 (iKON 2), Synergy 516 (Brain 2), Oxy 2 (Falcon 12) Graupner MZ-32 Experience is something you gain only after you need it. I wouldn't mind social media so much if it didn't involve people. |
06-11-2012, 05:11 PM | #4 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2010
|
I got it I had the sensor in the wrong port know I just have to figure out how to do the endpoints I am getting weird motor off number of -136 and no matter where the motor on it does not change the rpm this is with a cc ice 120
__________________
RCHN Citizen 790 -Protos maxv2 evo,xnova,Hw160, xpert, brain-Logo 600sxv2, hw130, mks scorpion,optipower,brainProtos -380 evo,Mks,xnova,HW,pulse,brain2. Jeti ds16 |
06-11-2012, 05:39 PM | #5 (permalink) |
Registered Users
Join Date: Sep 2010
|
What I did was;
1. Set tx endpoints in the Vbar software for -100/100 in tx tab 2. Make sure gov is off in the Vbar. 3. Set esc up for airplane mode with auto calibrate end points. 4. Power up Vbar 5. Connect esc with throttle stick at high stick wait for tones then move to low stick. 6. Disconnect esc and change auto calibrate to fixed endpoints. 7. Power up and go to gov screen and turn it on. Make sure to press reset. 8. Follow Mr. Mel's video on setting the endpoints. All of my CC escs has a narrow window of resolution. Mid -60's on low and mid +60's on high. |
06-11-2012, 05:44 PM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2010
|
yea thats what I just came up with -70 to 70 when the the spoolup first starts it goes normal then pauses for a half a second then continues on with the spoolup this happens on my mini protos with a hw esc does anyone know how to fix this or is it just the way it is
__________________
RCHN Citizen 790 -Protos maxv2 evo,xnova,Hw160, xpert, brain-Logo 600sxv2, hw130, mks scorpion,optipower,brainProtos -380 evo,Mks,xnova,HW,pulse,brain2. Jeti ds16 |
06-11-2012, 05:50 PM | #7 (permalink) |
Registered Users
Join Date: Sep 2010
|
I beleive from 5.2 on, it has an initial jump on the motor due to some motors having troubles starting correctly. Don't quote me on that though.
|
06-11-2012, 05:56 PM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2010
|
so its like a jumpstart for the motor i think ive read that somewhere to
__________________
RCHN Citizen 790 -Protos maxv2 evo,xnova,Hw160, xpert, brain-Logo 600sxv2, hw130, mks scorpion,optipower,brainProtos -380 evo,Mks,xnova,HW,pulse,brain2. Jeti ds16 |
Thread Tools | |
Display Modes | |
|
|