Register Now

raptor90wm · 01-08-2015, 12:49 AM

Ok I'm ready to madin my trex 550v2 with gpro unit, but i don't know where to plug in my second bec cable. Can I use a free port?

Smoggie · 01-08-2015, 02:00 AM

If it's not already being used to power a receiver you can use the 'battery out' port which is the one of the two that sits horizantally along the bottom, below where the servos plug in.

The only connections that you cant use to feed power in are the two intended for the receiver signal wires to connect to, they are the last two on the right.

raptor90wm · 01-08-2015, 02:34 AM

Oh sorry, I forgot to say I'm using sats only.
So I plug one into, battery port, at the bottom, and the second into battery out port at the bottom? Just for clarification and to be certain.

Also could you tell me, there is cyclic expo in parameter menu, set to 15.
So when I want to adjust expo, do I adjust It in the software or the transmitter?

Thanks for your help

Smoggie · 01-08-2015, 06:27 AM

Quote:

Originally Posted by raptor90wm

So I plug one into, battery port, at the bottom, and the second into battery out port at the bottom? Just for clarification and to be certain.

Yes, that's right.

Only caveat I'll add is that I'm basing this advice on my experience with the 3GX, which has identical pin-out arrangement to the Gpro..... I've not used an actual Gpro.

For that reason I can’t help with the menu, sorry.

TR450ZS · 01-08-2015, 11:46 AM

Grumpy is quite correct. I have done this on my 600's GPRO

raptor90wm · 01-08-2015, 12:15 PM

I had my madin and all went well after I got the tail dialed in.

So can you tell me is expo in the software or the transmitter?

01-08-2015, 12:49 AM	#1 (permalink)
raptor90wm Registered Users Join Date: Feb 2012	where to plug second bec lead? Ok I'm ready to madin my trex 550v2 with gpro unit, but i don't know where to plug in my second bec cable. Can I use a free port?

01-08-2015, 02:00 AM	#2 (permalink)
Smoggie Registered Users Join Date: Nov 2013 Location: Aberdeen, UK	If it's not already being used to power a receiver you can use the 'battery out' port which is the one of the two that sits horizantally along the bottom, below where the servos plug in. The only connections that you cant use to feed power in are the two intended for the receiver signal wires to connect to, they are the last two on the right. __________________ Gob 700 BT 'T' \| SoXos Strike 7.1 \| Henseleit TDR, TDF, TDSF & TDR2 \| OMP M1&M2 \| UK stockist for OMPHobby M1/M2 ScotiaRC.co.uk

01-08-2015, 11:46 AM	#5 (permalink)
TR450ZS Registered Users My HF Map location Join Date: Apr 2013	Grumpy is quite correct. I have done this on my 600's GPRO __________________ Allan TREX 250 PRO,Talon15, GPRO, Zeal ----TREX 500 EFL PRO, GPRO, RAILS ----2x TREX 450PRO V2, 1xGPRO&1xBRAIN, Talon35, RAIL , Zeal ---- SAVOX powered TREX500 EFL in Roban scale UH1-N ---- TREX 600 EFL PRO, GPRO, RAILS ---- DX9 ----

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-08-2015, 02:34 AM	#3 (permalink)
raptor90wm Registered Users Thread Starter Join Date: Feb 2012	Oh sorry, I forgot to say I'm using sats only. So I plug one into, battery port, at the bottom, and the second into battery out port at the bottom? Just for clarification and to be certain. Also could you tell me, there is cyclic expo in parameter menu, set to 15. So when I want to adjust expo, do I adjust It in the software or the transmitter? Thanks for your help

01-08-2015, 12:15 PM	#6 (permalink)
raptor90wm Registered Users Thread Starter Join Date: Feb 2012	I had my madin and all went well after I got the tail dialed in. So can you tell me is expo in the software or the transmitter?

Register Now

Log-in