Post your Logo pictures here!

[dyin2fly]

Originally Posted by mhills51

Here is a pic with the orange.

I like the orange better than the red

[mhills51]

Originally Posted by dyin2fly

I like the orange better than the red

The orange was fine, but I have two sets of these blades and tail blades and it just was not working lol! If you want the canopy it is sold at oomodel for $47 http://www.oomodel.com/logo-600-cano...2-p-64000.html they have two others as well.

[andione1983]

heres mine

[richardmills]

all ready for maiden, and its snowing!

[andione1983]

Nice^

Sent from my GT-I9100 using Tapatalk 2

[Mr.Gobler]

looks good, might want to trim that motor shaft it will get close to battery..and puncture it

this photo,,

[stew70]

thats the yge super combo?

[richardmills]

Originally Posted by itsparks

looks good, might want to trim that motor shaft it will get close to battery..and puncture it

Thanks. Theres plenty of room with my packs and i may add the counter bearing so didnt want to cut it just yet.

Originally Posted by stew70

thats the yge super combo?

Nearly. Its the hacker super combo without the hacker.

[ady]

hi mr mills , the logo look is growing on me and yours looks great , also learning the different sizes , can i ask what blades and battery you`ll be using please

ady

[Mr.Gobler]

Originally Posted by richardmills

Thanks. Theres plenty of room with my packs and i may add the counter bearing so didnt want to cut it just yet.

just warning you to be carefully is all, if you crash or hard land that shaft will go right into a pack and start a fire.. trust me.. I seen it already..

Sent from my SGH-I747M using Tapatalk 2

[mhills51]

Most of the guys at our field made little metal or CF plates that they velcro to the top of the packs. They also use the same plank to slide under the battery to lift it off the velcro and slide the battery out.

[Mr.Gobler]

Originally Posted by mhills51

Most of the guys at our field made little metal or CF plates that they velcro to the top of the packs. They also use the same plank to slide under the battery to lift it off the velcro and slide the battery out.

good good, just don't want to see another logo fire, did u see last week's?

Sent from my SGH-I747M using Tapatalk 2

[richardmills]

Originally Posted by ady

can i ask what blades and battery you`ll be using please

Hi. I'm going to be using 6s 4000s as thats what I'm using in my tdr. I'm only going to run about 2050 headspeed.

The blades are 523s as supplied as part of the kit. I may try 553s as I like the floaty feeling.

[ady]

Awesome , thanks for that , I still have a lot to learn with the logo , good luck flying yours , I gotta wait another week or so before me 550sx gets a whirl

[gregleprothesiste]

my logo600 :

[irresponsibility]

Logo 600 SX with Pyro 700-52, Jive 80, BLS950/Fut BLS256HV, Silverline Vbar and Glacier 12s 8ah pack set. Also have the carbon frame and canopy that I bought together used from this forum.

So smooth that it threw me off guard... I didn't have to adjust a thing mechanically on the maiden flight. I did a gain change, tail/cyclic optimization and a trim flight and just let it float. Truly amazing, and more than I was expecting from such a simple design.

[Underscore]

Originally Posted by itsparks

looks good, might want to trim that motor shaft it will get close to battery..and puncture it

What's the best way to cut off the shaft? Dremel? Put the whole motor into a lathe?

[GimpyGolden]

Dremel works great, better with fiber reenforced wheel.
Make sure you put the motor in a baggie/tape and just poke the shaft through. This prevents and shavings/filings from being pulled into the motor and sticking to mags.

[Mr.Gobler]

Originally Posted by GimpyGolden

Dremel works great, better with fiber reenforced wheel.
Make sure you put the motor in a baggie/tape and just poke the shaft through. This prevents and shavings/filings from being pulled into the motor and sticking to mags.

exactly,

I went a step further and put tape around all the vent holes too, AND used the baggie

[mhills51]

Well looking to maiden mine in a day or two, so I thought I would take some close ups while it is still in one piece lol!