START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
mCP X Brushless Mods Blade Micro CPx Brushless Mods and Conversions |
|
LinkBack | Thread Tools | Display Modes |
04-17-2012, 11:49 AM | #41 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
My new wiring is much more clean, it's not so hard
|
Sponsored Links | |||
Advertisement |
|
04-17-2012, 03:23 PM | #42 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
All is connected, but i have still the same problem. The receiver cut.
I'll try another receiver |
04-17-2012, 09:45 PM | #43 (permalink) | |
Registered Users
Join Date: Nov 2008
|
Quote:
Perhaps under load the voltage is dropping out of the rx's range or the servos, mb or wire are starving it for current. I'd be testing it with a largish 1s too or parallel a couple just to eliminate the lipo for now. Amp |
|
04-18-2012, 01:56 AM | #44 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
I change yesterday my receiver, and it work better.
I think my receiver had a problem. I made my first fly this morning. The bird is shaking a lot. My anti rotation guide moved, my receiver is hanging. I will prepare my receiver and re re wire |
04-18-2012, 03:20 AM | #45 (permalink) |
Registered Users
|
A question. Can you easily set 6 degrees of cyclic pitch to the J point of the MB setup?
|
04-18-2012, 08:16 AM | #46 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
I use 2 middle servo connecting point to have a symetruc pitch in positiv and negativ.
At about 6° (it's not so easy to mesure) the led is blue. It's not optimal but good enough. To mesure the 6° I took my xtreme pitch gauge, i try not to touch the blade, put the gauge frame horizontal and the clip the balde in the gauge. The weight of the gauge make easily move the value from few °. |
04-19-2012, 01:47 AM | #47 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
I will change the motor and the esc. All the elec on a 1s batterie is to much.
Anyone interested in a HP08S 16500KV + XP-12 + prog card ? |
04-20-2012, 12:57 AM | #48 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
So i will go on a 3s liftbag version to avoid all my elec problem.
i am designing a new frame to balance the 22gr of batterie. i'll probably put the main motor in the back, in fact i'll invert all the 3 servo and the motor. |
04-23-2012, 06:03 AM | #49 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
All is order !!
Just have to wait.. |
04-23-2012, 06:08 AM | #50 (permalink) |
Registered Users
Join Date: Dec 2011
|
sounds like something out of a frankenstein movie! Looking forward to seeing the results!
|
04-23-2012, 10:00 AM | #51 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
not bad for a name,
frankenMCPX I am on my new frame, which will be a bit lighter than the old one. |
04-23-2012, 10:16 AM | #52 (permalink) |
Registered Users
Join Date: Oct 2007
|
very cool stuff going on here but want to see video!
|
04-23-2012, 10:51 AM | #54 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
I had a small calculation today, after few PM with lifbag.
Heli / Rotor RPM / Rotor Diameter / Blade speed X7 Goblin 2200 1600mm 650Km/h T-rex 500 3200 980mm 590Km/h T-rex 450 3800 710mm 510km/h t-rex 250 4700 460mm 400km/h MCPX liftbag 7400 240mm 334km/h It seems to be not bad. It make a beautifull linear curve Last edited by fury118; 04-23-2012 at 12:03 PM.. |
04-23-2012, 04:34 PM | #55 (permalink) |
Registered Users
Join Date: Dec 2010
|
I can't wait to see how this thing flies, Nice work!!
|
04-25-2012, 11:10 AM | #56 (permalink) |
Registered Users
Join Date: May 2009
|
Some of you guys have seen this video but it's a good one. Stay motivated. We want to see this thing fly!
[ame]http://www.youtube.com/watch?v=b29Msu_7_sE[/ame] Edit for super fail on embeding youtube video LOL |
04-25-2012, 11:22 AM | #57 (permalink) |
Registered Users
|
The project will come in handy when the 130x modding starts, im looking forward to your progress.
|
04-25-2012, 12:00 PM | #58 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2012
|
I am looking to have a flying heli ready for the 19-20 mai for the 3D cup in france
The CAD is ready, i will make the frame before next week, i am waiting all my orders and will build it fast. Wait and see. I want to give the heli to test to good 3d pilot to see what they think about it. |
Thread Tools | |
Display Modes | |
|
|