Register Now

rctintin · 06-06-2014, 08:36 PM

Guys, I usually use 6203SB Rx's, and have loads of them, all trouble free. I am trying to use the R7008SB so I can add telemetry to one of my Heli's. I have bound it from the bind screen in my 18MZ, and its LED has gone green, but there is no signal to my V-Bar.

Its plugged into the 8/SB slot (Signal wire to the top). If however I plug it into the S-Bus2 slot at the bottom of the Rx, I get an output signal, and the V-bar works fine.

Surly this is incorrect, because I need to add my Telemetry sensor into S-Bus2 slot?

Thanks, Rob.

dpelletier · 06-06-2014, 10:36 PM

Your receiver is probably in channel mode A... you'll want to change it to channel mode B.

rctintin · 06-07-2014, 01:12 PM

Thank you my friend, exactly right. Changed it to 2 blinks for mode B and it's now outputting S-Bus on Ch8SB

dpelletier · 06-07-2014, 10:47 PM

Thank you for asking how I knew...

All is good in the end

Mercuriell · 08-02-2014, 04:39 AM

Just spent days trying to figure this - thank you

: really small print in that Rx info sheet, have to know what you're looking for before you see it

:

06-06-2014, 08:36 PM	#1 (permalink)
rctintin Registered Users Join Date: Jul 2009	No S-Bus signal on a R7008SB - have to configure mode! Guys, I usually use 6203SB Rx's, and have loads of them, all trouble free. I am trying to use the R7008SB so I can add telemetry to one of my Heli's. I have bound it from the bind screen in my 18MZ, and its LED has gone green, but there is no signal to my V-Bar. Its plugged into the 8/SB slot (Signal wire to the top). If however I plug it into the S-Bus2 slot at the bottom of the Rx, I get an output signal, and the V-bar works fine. Surly this is incorrect, because I need to add my Telemetry sensor into S-Bus2 slot? Thanks, Rob. __________________ TDRx2, Synergy N7/E7se/N5cTT, Align 450L/550/700e/700n, Gaui NX7/NX4, , Goblin 700/Black Nitro, Futaba 18MZ/ V-Control All on V-Bar's and S-Bus. #0095 Last edited by Mercuriell; 08-02-2014 at 04:40 AM..

06-06-2014, 10:36 PM	#2 (permalink)
dpelletier Registered Users My HF Map location Join Date: Apr 2010	Your receiver is probably in channel mode A... you'll want to change it to channel mode B. __________________ Futaba 14SG, Synergy E5, Furion 6, Beam E4(v1) FBL, CGY750, Skookum

06-07-2014, 01:12 PM	#3 (permalink)
rctintin Registered Users Thread Starter Join Date: Jul 2009	Thank you my friend, exactly right. Changed it to 2 blinks for mode B and it's now outputting S-Bus on Ch8SB __________________ TDRx2, Synergy N7/E7se/N5cTT, Align 450L/550/700e/700n, Gaui NX7/NX4, , Goblin 700/Black Nitro, Futaba 18MZ/ V-Control All on V-Bar's and S-Bus. #0095

06-07-2014, 10:47 PM	#4 (permalink)
dpelletier Registered Users My HF Map location Join Date: Apr 2010	Thank you for asking how I knew... All is good in the end __________________ Futaba 14SG, Synergy E5, Furion 6, Beam E4(v1) FBL, CGY750, Skookum

08-02-2014, 04:39 AM	#5 (permalink)
Mercuriell HF Support Join Date: Sep 2006	Just spent days trying to figure this - thank you : really small print in that Rx info sheet, have to know what you're looking for before you see it : __________________ John

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in