START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Futaba CGY750 FBL System Futaba CGY750 Help and features Support Forum |
|
LinkBack | Thread Tools | Display Modes |
06-10-2016, 01:39 PM | #1 (permalink) |
Registered Users
Join Date: Jun 2009
|
Well im all in. F3C and general setup questions
Going all in on Futaba. whent from vBar neo to this:
My focus is F3C, and im using a SAB Urukay comp 3 blade heli. I seen all Nicks videos on how to setup 2.0, but still some question already comes to mind. 1: Head gain. Can i set the gain for ELEV and AIL independent or is the headgain for both? 2: In tail setup, where you setup the "ANG" ( rotation speed ). Can you have different rotation speed under the different fligth modes? Or do you have to adjust that with dualrate in the radio? 3: During setup and "servo type". My Hitec HSB-9360Th is 333Hz servo, should I put in 333 or leave it at stock 285? 4: During swash setup and cyclic rate "SWS rate". I use 3 blade head with 3x 725mm heavy blades. Should I use 10 degrees as stated in the manual for a 800 size, or is it any different for a 3 blade head? Also as I am going to use one "bank" for hovering that I whant as stable as possible, should I use a lower cyclic pith in this "bank" ? Or use the same and then use another parameter to change the hover "bank" ? Thats it for now. Thanks for helping And sorry for my bad English
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
Sponsored Links | |||
Advertisement |
|
06-11-2016, 09:24 PM | #2 (permalink) | |
Registered Users
Join Date: Feb 2008
|
Quote:
No one more knowledgeable has answered so I'll give it a go. See above, good luck. Personally I really like the 750, I would love to hear your thoughts on it after you get a chance to become familiar with it. Lance
__________________
Futaba 14SG / Synergy E6 / CGY750 |
|
06-12-2016, 12:19 AM | #3 (permalink) |
Registered Users
Join Date: Jul 2007
Location: Melb, Oz
|
I'm setting up the CGY for the first time and want a good F3C setup start point for the Version 2 firmware so hopefully we will get some more knowledgeable guys commenting soon. There is a great post for the earlier firmware for F3C setup and it would be great to see a similar post for v2.
//Dennis.
__________________
soXos: Strike 8.1 - Strike 7.1 Light - Strike 6.1 : Goosky: RS7 - RS4 - S2 - S1 soXos DB7 nightflyer : Jeti DS-16 & DS-12 I am www.soxosaustralia.com.au | soXos helis | 1st-RC Products | EGODRIFT motors | Goosky helis | Spinblades |
06-12-2016, 04:14 AM | #4 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2009
|
Thanks for helping !
Under gyro menu in the radio, I now see both "rudd" "ail" and "elev", should I just ignore "elev" when I set my cyclic gain?
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
06-13-2016, 10:18 AM | #5 (permalink) | |
Registered Users
Join Date: Feb 2008
|
Quote:
On the home screen of the 750 it shows you what the gain settings are, you can verify you are changing the right one by verifying the change there.
__________________
Futaba 14SG / Synergy E6 / CGY750 |
|
06-13-2016, 11:04 AM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2009
|
thanks
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
06-16-2016, 07:21 AM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2009
|
More questions:
During swash setup. My servo horns are 90, swash is leveled. Zero pitch at midstick. But my max and min pitch differ 1.3 degrees. I tried to play around with the links, but the error is consistent, always 1.3 degrees error between max/min. I tried to use the servo end points in the radio with great success. If I use 109 instead of 100 on the pitch channel for "min" pitch, I get equal pitch numbers. I then "relearned" the CGY750 in the pitch min/zero/max menu. Is this a ok way to solve this, or should I go another route? Thanks
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
06-17-2016, 07:36 AM | #8 (permalink) |
Registered Users
Join Date: Jun 2013
|
I would have told you to do just that. however, I had this same issue setting mine up. Nick told me to adjust it out with the pitch curve and not the endpoints.
__________________
Gasser Mike Team KDE Direct, TRM Power, Byron Fuels, MKS Servos |
06-17-2016, 08:25 AM | #9 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2009
|
Hmm ok..
I wounder if that is better to keep the linearity to use the pitchcurve vs endpoints?
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
06-17-2016, 05:43 PM | #10 (permalink) |
Registered Users
Join Date: Feb 2008
|
I would have said the same, what's the difference between the two methods when it gets to the receiver/750. Seams to me the resultant signal would be the same.
__________________
Futaba 14SG / Synergy E6 / CGY750 |
06-20-2016, 07:23 AM | #11 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2009
|
did som test with this today.
I first used "servo travel" and then "pitch curve" only to set up my pitch curve to be equal at max +-. And I watched the numbers in the CGY at min/zero/max pitch menu while doing this. The numbers (uS) is the same at max/min pitch no matter what method I use. So to me this shows that the CGY dont care what method you use to achive this.
__________________
Futaba CGY-750/ Align 760x F3C x2 / |
Thread Tools | |
Display Modes | |
|
|