Register Now

XSTAR · 07-12-2011, 09:36 PM

Just wondering if you guys had the same results as i did, when i updated my 3g units to v3 my rolls were super slow and on 2.1 they were insane fast? I just checked my servo movement in the software and i was at 260 left and right and thats at 90, should i up it to 100?

Thanks guys...

K2Freak · 07-12-2011, 10:31 PM

I noticed only that the tail got much better - I added 10 gyro sens points. I had to run DIR mode on both of mine and one of them lost servo centering, but all in all much better software, IMO.

You might post to the 3G forum to see if anything went wrong during your upgrade??

XSTAR · 07-15-2011, 08:39 PM

Anyone know how to make it roll like it did using v2.1 besides going back to it?

kodiak ak · 07-15-2011, 08:55 PM

If you have good cyclic pitch in DIR mode.12 to 14 deg. depending on your flying style. (refer to your manuel on how to check this) use your 3g link and up the # on the aileron control rate.

willl

XSTAR · 07-15-2011, 09:16 PM

I have 12 cyclic degrees and its set at 90, on v2.1 i had to lower the rates...Im lost..

K2Freak · 07-16-2011, 12:18 AM

You simply increase swash mix. But that does not tell you what happened ...

XSTAR · 07-16-2011, 12:27 AM

Using dx8 these are my swash values
Ail +100
Ele +100
Pit +48

Weird, when in dir mode at mid stick checking for cyclic pitch it says to push left and adjust for 12 degrees, then when going through the setup it says to push right and im getting 14 degrees?? Im lost..

Does this look right?

XSTAR · 07-16-2011, 09:10 AM

Anyone know?

K2Freak · 07-16-2011, 10:36 AM

Have you checked here? 3G forum is a better place for 3G specific questions.

https://www.helifreak.com/forumdisplay.php?f=222

There is definitely something wrong if you are set at 100% swash mixing and your control rate is slow. That does not add up. Did you cut your servo throws down? Are your mechanics centered accurately? i. e. did you use a lot of subtrim on any servo? I have heard of some oddity when that is the case.

07-12-2011, 09:36 PM	#1 (permalink)
XSTAR Registered Users Join Date: Aug 2008	Updated 3g to v3 and rolls are slow Just wondering if you guys had the same results as i did, when i updated my 3g units to v3 my rolls were super slow and on 2.1 they were insane fast? I just checked my servo movement in the software and i was at 260 left and right and thats at 90, should i up it to 100? Thanks guys... __________________ DX8 \| TREX 700E \| BEASTX \| CC80HV \| 700MX \| AR8000 \| HW 15Amp UBEC \| DX8 \| TREX 550E \| BEASTX \| 600MX \| CCBEC PRO \| 70G ESC \| AR8000 \| HELIIMAGE Printed BOOM WRAPS & CUSTOM CANOPY NAME

07-12-2011, 10:31 PM	#2 (permalink)
K2Freak Registered Users My HF Map location Join Date: Mar 2009 Location: Samish Island, WA	I noticed only that the tail got much better - I added 10 gyro sens points. I had to run DIR mode on both of mine and one of them lost servo centering, but all in all much better software, IMO. You might post to the 3G forum to see if anything went wrong during your upgrade?? __________________ AMA 373608

07-15-2011, 08:39 PM	#3 (permalink)
XSTAR Registered Users Thread Starter Join Date: Aug 2008	Anyone know how to make it roll like it did using v2.1 besides going back to it? __________________ DX8 \| TREX 700E \| BEASTX \| CC80HV \| 700MX \| AR8000 \| HW 15Amp UBEC \| DX8 \| TREX 550E \| BEASTX \| 600MX \| CCBEC PRO \| 70G ESC \| AR8000 \| HELIIMAGE Printed BOOM WRAPS & CUSTOM CANOPY NAME

07-15-2011, 09:16 PM	#5 (permalink)
XSTAR Registered Users Thread Starter Join Date: Aug 2008	I have 12 cyclic degrees and its set at 90, on v2.1 i had to lower the rates...Im lost.. __________________ DX8 \| TREX 700E \| BEASTX \| CC80HV \| 700MX \| AR8000 \| HW 15Amp UBEC \| DX8 \| TREX 550E \| BEASTX \| 600MX \| CCBEC PRO \| 70G ESC \| AR8000 \| HELIIMAGE Printed BOOM WRAPS & CUSTOM CANOPY NAME

07-16-2011, 12:18 AM	#6 (permalink)
K2Freak Registered Users My HF Map location Join Date: Mar 2009 Location: Samish Island, WA	You simply increase swash mix. But that does not tell you what happened ... __________________ AMA 373608

07-15-2011, 08:55 PM	#4 (permalink)
kodiak ak Registered Users Join Date: Feb 2011	If you have good cyclic pitch in DIR mode.12 to 14 deg. depending on your flying style. (refer to your manuel on how to check this) use your 3g link and up the # on the aileron control rate. willl

07-16-2011, 12:27 AM	#7 (permalink)
XSTAR Registered Users Thread Starter Join Date: Aug 2008	Using dx8 these are my swash values Ail +100 Ele +100 Pit +48 Weird, when in dir mode at mid stick checking for cyclic pitch it says to push left and adjust for 12 degrees, then when going through the setup it says to push right and im getting 14 degrees?? Im lost.. Does this look right? __________________ DX8 \| TREX 700E \| BEASTX \| CC80HV \| 700MX \| AR8000 \| HW 15Amp UBEC \| DX8 \| TREX 550E \| BEASTX \| 600MX \| CCBEC PRO \| 70G ESC \| AR8000 \| HELIIMAGE Printed BOOM WRAPS & CUSTOM CANOPY NAME

07-16-2011, 09:10 AM	#8 (permalink)
XSTAR Registered Users Thread Starter Join Date: Aug 2008	Anyone know? __________________ DX8 \| TREX 700E \| BEASTX \| CC80HV \| 700MX \| AR8000 \| HW 15Amp UBEC \| DX8 \| TREX 550E \| BEASTX \| 600MX \| CCBEC PRO \| 70G ESC \| AR8000 \| HELIIMAGE Printed BOOM WRAPS & CUSTOM CANOPY NAME

07-16-2011, 10:36 AM	#9 (permalink)
K2Freak Registered Users My HF Map location Join Date: Mar 2009 Location: Samish Island, WA	Have you checked here? 3G forum is a better place for 3G specific questions. https://www.helifreak.com/forumdisplay.php?f=222 There is definitely something wrong if you are set at 100% swash mixing and your control rate is slow. That does not add up. Did you cut your servo throws down? Are your mechanics centered accurately? i. e. did you use a lot of subtrim on any servo? I have heard of some oddity when that is the case. __________________ AMA 373608

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in