Raptor 30/50 V2 airframe and huge parts assortment, metal head/swash

[conefree]

Bought this stuff off ebay a while back with the intention of converting my Raptor 30 to a Raptor 50. I no longer have the Raptor 30 and would like to get this stuff to somebody who would use it.

Pic of the entire lot:
http://s37.photobucket.com/albums/e7...t=IMG_9367.jpg






Full collection of pics here with more detail shots: http://s37.photobucket.com/albums/e75/conefree/Raptor%20V2%20frame%20and%20parts/

• Complete 30V2 frame, one minor flaw. Crack on the back left side near top of fuel tank. Remote tail servo mounting tray, upgraded clutch bell. Complete with fan, clutch, gears and auto hub
• 1 set 600mm fiberglass blades
• Full metal HTR flybar head, came to me with feathering shaft bent. Replaced and repaired, otherwise in good shape
• Metal swashplate
• Carbon graphite base plate, cracked as shown
• Brand new fiberglass canopy, just needs a clip installed, which is also included. There are a couple cracks from shipping, noted by the arrows. Nothing major, just feel the need to point them out
• 4 AK0174 belts
• Complete tail boom and tail rotor assembly, metal tail rotor case, fully functional tail rotor
• PV0328 tail boom supports
• 1 set of longer tail boom supports (presumably for 50)
• 1 set NIP landing gear
• Main frame spacers
• 1 set standard flybar paddles
• 1 set blue thunder tiger flybar paddles
• 1 set unknown flybar paddles
• 7 flybar hoops
• 1 seesaw bar
• 7 washout control linkages
• 10 flybar control levers
• 4 flybar control arms
• 1 main rotor hub
• 2 main blade grips
• 2 washout bases
• 1 elevator control arm
• 2 main shaft locking rings
• 2 head dampeners
• 16 Assorted bearings
• 2 flybar cage rods
• 2 extra 85 tooth gears
• 1 100 tooth gear
• 2 extra main shafts, one is new, one has a slight bend in it, could be straightened if you choose
• 1 extra fan
• 2 extra clutch bells with pinion
• 1 clutch liner, may or may not be usable
• 1 extra collective servo tray
• 2 flybars (one slightly bent, could be straightened)
• 4 vertical tail fins, 3 are painted
• 1 tail hub assembly with broken tail pitch control link, grips and hub intact with bearings
• 1 horizontal fin
• 4 tail blade grip halves
• 1 tail rotor case
• 2 aluminum engine mounts
• 3 tail boom support brackets that mount to horizontal fin
• 5 tail blades
• 3 big idler pulleys
• 2 small idler pulleys
• 2 tail rotor hubs with bearings
• 1 tail rotor shaft
• 2 tail servo linkage connector block
• 2 tail pulleys
• 2 tail pulley pins
• 4 pins for tail linkage arms
• 4 tail pitch slider bushings
• 3 tail pitch sliders
• Various link rods and link ends

http://s37.photobucket.com/albums/e75/conefree/Raptor%20V2%20frame%20and%20parts/

The head and swashplate alone are worth $230 new. All told, well over $600 worth of stuff here, with enough to make a full helicopter and then some. Looking for $250 shipped in CONUS, other locations can be negotiated. Also willing to entertain offers. Thanks!

[u8at711]

pm'ed

[u8at711]

payment sent,

[conefree]

Sold!