TWO Align TRex 700E with CHP DL frames upgraded like mad!

[TT]

I'm finally parting with my Custom Heli Parts DL framed 700Es. I've been flying these helis for a few years now. I'm selling my 'backup' (under 50 flights, great condition) and enough parts to build a complete NEW airframe. My 'primary' airframe was totaled in a severe crash and I sold what was left to a local guy so almost all of the spare parts listed here are new with zero flights.

Over the years of flying these I had gone through and improved anything I felt needed improving. Yes, I went upgrade crazy on these but the results were totally worth the effort. These are very reliable airframes and parts are easy to get. Due to the exceptionally low weight you can get great performance with 120A or even 100A motor/esc combos. I had been flying these with Savox 5065 500KV motors (100A continuous rating) and didn't feel the desire for more power.

Recently I moved the ESC to the rear so I could run heavier packs and still balance well and added a capacitor bank to compensate for the additional lead length. While this setup works well I still believe that a light ESC up front makes wiring much easier and would be lighter overall with slightly smaller lipos. If needed the tail servo could be relocated to the boom to help with balance.

Here's what I have. Everything listed here is on the built / used airframe AND ALSO new for the unbuilt airframe (unless otherwise noted):

TRex 700E V2 head (non-DFC), bearing blocks, boom block, etc.
CHP DL carbon frame set
Quick UK balls everywhere
Quick UK links everywhere
Quick UK carbon fiber tail pushrod
Quick UK tail pushrod ends
Quick UK tail rod guide
Quick UK Servo arms (specifically for DL frameset, Futaba splined)
3Racing 3mm titanium turnbuckles
RC Booya quick-release canopy mounts
Lynx main spindle bolts
Curtis Youngblood Rave ENV Boom Support Set
Curtis Youngblood Rave ENV Boom Support Brace
Align 104T M1 Autorotation tail drive slant gear (black gear, V3 ratio)
Align M1 Torque Tube Front Drive Gear Set (21T) (black gears, V3 ratio)
Align Torque Tube Rear Drive Gear Set w/tail hub (black gears)
Align Aluminum tail grip set
Align V3 tail shaft / hub set
Align F3C low profile landing gear strut (mounted on front for more tail clearance)

Canomod Urenus canopy (used, tipover rash / paint chips, cracks) [used airframe only]
Align Rear Frame Mounting Block [used airframe only]
CHP extended tail fin [used airframe only]
Scorpion battery straps + 1 new spare [used airframe only]
YEP 120HV ESC with custom capacitor pack [used airframe only]

Spares:
Align 3rd main bearing block
Align boom support set
Align 700-800 Blade Clips
KBDD lime green dampeners (2 sets)
PureTech battery straps
Align plastic tail grips with KDE direct update kit
Quick UK Trex 700 Carbon Tail Pushrod 5.5mm x 740mm (29")
Loads of Align fasteners, ball links, balls, etc.
MUCH more to be listed later...

I also have 5 unused Canomod canopies available that will fit these airframes but might need to be re-drilled.

For more info on these type airframes see this thread I started a few years ago:
https://www.helifreak.com/showthread.php?t=343852

Note: No electronics included other than the pictured ESC and associated wiring. No main or tail blades included.















I'm looking to get $600 for all of this plus shipping. Shipping from Thailand OR the USA...I'll be flying to the USA early September and will bring it with me if needed. No trades.

[TT]

$500 OBO. I'm flying to the USA soon and would like to bring these with me. May separate into two airframes. PM me. Check my feedback, buy with confidence.

[TT]

$400 OBO. I need to sell these SOON.

[TT]

$350 shipped in Continental USA for EVERYTHING. I fly to the USA in two days so let me know ASAP.

[TT]

TTT

[TT]

no longer available