Register Now

Bink1989 · 06-19-2015, 08:36 PM

I am not sure how to word this. So let me try the best I can. I recently bought a blade 450x. It didn't have the flybarless system on is so I had to purchase that. However horizonhobby no longer offers the AR7200BX the replacement is AR7300BX. They are both the exactly the same. I have recently started flying helicopters. So I am not sure how to hook the servos up to the flybarless system and what channel each servo goes to. Any help would be greatly appreciated.

prismatic · 06-19-2015, 08:58 PM

I wish I could help but have never flown a blade. Only familiar with Trex 450. But the elevator servo plugs into "elev", aileron into "aile"and pitch into "aux1". It pretty easy to setup the BeastX, just read the manual and follow the steps.

Bink1989 · 06-19-2015, 09:19 PM

I know which servo is the tail servo however I am not sure which servo is the aileron which on is elevator and which one is pitch. The way the Blade 450X is setup is I have one servo on the front close to the battery, and two servos in the back behind the motor. The servo in the front connects to the front swash plate and the servos in the back connect to the side of the swash plate. Idk if that helps or not.

CrashNburn420 · 06-19-2015, 09:56 PM

The servo in the front will be elevator. The other two will be aileron and aux1. Look up videos on YouTube for setting up the ar7200bx.

Post this in the 450 x forum and you will get a lot more help. I had a 450x but it's been a long time since I set it up.

AR7200BX How To Complete Initial Setup Guide (19 min 48 sec)

Bink1989 · 06-20-2015, 08:30 AM

Quote:

Originally Posted by CrashNburn420

The servo in the front will be elevator. The other two will be aileron and aux1. Look up videos on YouTube for setting up the ar7200bx.

Post this in the 450 x forum and you will get a lot more help. I had a 450x but it's been a long time since I set it up.

AR7200BX How To Complete Initial Setup Guide - YouTube

Will it matter which servo I connect to aileron and witch servo is connected to aux1?

CrashNburn420 · 06-20-2015, 10:49 AM

The aileron servos are plugged into aux1 & aileron, doesn't matter which servo is plugged into either one. However once you have done your setup, you can't switch those unless you redo the setup again. If you haven't watched them yet, you should look at the videos on setting up the beast x. They're in the beastx category on here and at the top in the stickies.

06-19-2015, 08:36 PM	#1 (permalink)
Bink1989 Registered Users Join Date: Jun 2015	Blade 450 AR7200BX setup I am not sure how to word this. So let me try the best I can. I recently bought a blade 450x. It didn't have the flybarless system on is so I had to purchase that. However horizonhobby no longer offers the AR7200BX the replacement is AR7300BX. They are both the exactly the same. I have recently started flying helicopters. So I am not sure how to hook the servos up to the flybarless system and what channel each servo goes to. Any help would be greatly appreciated.

06-19-2015, 09:19 PM	#3 (permalink)
Bink1989 Registered Users Thread Starter Join Date: Jun 2015	Blade 450X I know which servo is the tail servo however I am not sure which servo is the aileron which on is elevator and which one is pitch. The way the Blade 450X is setup is I have one servo on the front close to the battery, and two servos in the back behind the motor. The servo in the front connects to the front swash plate and the servos in the back connect to the side of the swash plate. Idk if that helps or not.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-19-2015, 08:58 PM	#2 (permalink)
prismatic Registered Users Join Date: Jun 2015	I wish I could help but have never flown a blade. Only familiar with Trex 450. But the elevator servo plugs into "elev", aileron into "aile"and pitch into "aux1". It pretty easy to setup the BeastX, just read the manual and follow the steps.

06-20-2015, 10:49 AM	#6 (permalink)
CrashNburn420 Registered Users Join Date: May 2012	The aileron servos are plugged into aux1 & aileron, doesn't matter which servo is plugged into either one. However once you have done your setup, you can't switch those unless you redo the setup again. If you haven't watched them yet, you should look at the videos on setting up the beast x. They're in the beastx category on here and at the top in the stickies.

Register Now

Log-in