Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Gaui Helicopters > X5


X5 Discussion and support of the Gaui X5


Reply
 
LinkBack Thread Tools Display Modes
Old 12-04-2011, 06:15 PM   #1 (permalink)
Registered Users
 

Join Date: Dec 2006
Default Changing Beastx mounting orientation

I decided to move my Beastx from the side of the X5 to the bottom tray. This will change its mounting orientation from vertical to horizontal. I'm aware that I must make the change in Step A of the Beastx programming; however, is it also required that I go through the other programming steps, as well?
racin06 is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 12-04-2011, 06:51 PM   #2 (permalink)
Registered Users
 
Posts: 1,216
 

Join Date: Aug 2011
Default

it is not that hard to go through the settings again. I would go through it again. It is the control center of the heli. I wouldnt risk it. Spend few mins to setup will possibly save your heli.
czynot is offline        Reply With Quote Quick reply to this message
Old 12-04-2011, 07:29 PM   #3 (permalink)
Registered Users
 
Posts: 429
 

Join Date: Jun 2011
Default

Quote:
Originally Posted by racin06 View Post
I decided to move my Beastx from the side of the X5 to the bottom tray. This will change its mounting orientation from vertical to horizontal. I'm aware that I must make the change in Step A of the Beastx programming; however, is it also required that I go through the other programming steps, as well?
A E F I and M in setup I would reset due to them possibly getting reversed or something of that nature.

And also F in Parameter if your running Tail Pre-Comp.

Just do a whole new setup. Its quick.

Sent from my Droid Charge using Tapatalk.
superrmario is offline        Reply With Quote Quick reply to this message
Old 12-05-2011, 07:31 PM   #4 (permalink)
Registered Users
 
Posts: 14,707
 
My HF Map location
Join Date: Jun 2010
Default

if you dont go thew the set up again you will probably tip over on spool up, i changed mine from upright to upside down and every thing was set up wrong after that, glad i thought about it before i tried to fly it, it was one of those things where i was ready to go fly and i thought

wait just a minute, i better check this and i am glad i did.
__________________
-----------------------------------------------------------------

Blade 180 CFX, Sold the rest of my stuff, I dont really fly all that often any more.
dannylightning is offline        Reply With Quote Quick reply to this message
Old 12-05-2011, 09:26 PM   #5 (permalink)
Registered Users
 
Posts: 3,475
 

Join Date: Feb 2010
Default

Quote:
Originally Posted by dannylightning View Post
if you dont go thew the set up again you will probably tip over on spool up, i changed mine from upright to upside down and every thing was set up wrong after that, glad i thought about it before i tried to fly it, it was one of those things where i was ready to go fly and i thought

wait just a minute, i better check this and i am glad i did.
+1 your correction directions will more than likely be wrong
__________________
Trex 700e
hamstar78 is offline        Reply With Quote Quick reply to this message
Old 12-06-2011, 04:36 PM   #6 (permalink)
Registered Users
 
Posts: 1,551
 
My HF Map location
Join Date: Mar 2010
Default

^ correct. The only settings that needs to be changed when you update the unit orientation is A and M.

Check piro comp direction as well.

All of the other settings remain the same because you don't need to change the servo connections. Elevator servo is still the elevator servo, etc.
__________________
Stuff
Rob Cherry is offline        Reply With Quote Quick reply to this message
Old 12-06-2011, 08:14 PM   #7 (permalink)
Registered Users
 
Posts: 429
 

Join Date: Jun 2011
Default

Quote:
Originally Posted by csdstudio View Post
^ correct. The only settings that needs to be changed when you update the unit orientation is A and M.

Check piro comp direction as well.

All of the other settings remain the same because you don't need to change the servo connections. Elevator servo is still the elevator servo, etc.
I guess forget about I ? Swash plate Servo directions really arent nessesary.

Not being a smart ass, just being realistic. He is better safe than sorry.

Why take a chance?

Sent from my Droid Charge using Tapatalk.
superrmario is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

SEO by vBSEO 3.6.1