START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Flight Stabilization Flight Stabilization |
|
LinkBack | Thread Tools | Display Modes |
04-12-2014, 04:08 PM | #1 (permalink) |
Registered Users
Join Date: Mar 2014
|
Flymentor 3D Questions
I am just starting out and build my first hell (HK450). So a buddy of mine gave me his Flymentor 3D that he could never figure out. I mounted it to my HK450 and followed a set of videos from Cruzroy. I have a few issues to ask about. First when I try and 90 my servos using the trim in the Flymentor programming card, I get no response from the servos. They will not adjust up or down. Second, the flymentor is adjusting the wrong direction for the ailerons, how do I reverse this? Third, I was trying to use my gyro instead of the FM. But when I turn on the FM, the gyro doesn't light up. And lastly, when I try and take off (I manually adjusted the servos to get a level swash), the FM seems to do crazy things with the corrections. It adjusts right, left forward, back, with no rhyme or reason. I haven't even left the ground and I can see the blades moving all over the place. Could this be a gain setting on the CCD? BTW I am using a Turnigy 9x Tx.
Sorry for so many questions, but I have googled and googled but can't find a NOOB version of answers to these questions. |
Sponsored Links | |||
Advertisement |
|
04-12-2014, 05:48 PM | #2 (permalink) | |
Registered Users
Join Date: Jul 2010
|
Quote:
__________________
If it can be done wrong, I will find a way to excel at it. |
|
05-08-2014, 09:15 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2014
|
Ok so I built the 450 and did not put the Flymentor on. I could never get it set right and just gave up. Now I have an HK500 that I bought from a friend. I was trying again to install the Flymentor but again problems. I get the thing all hooked up and try and plug it in and nothing. I try to attach the programmer and won't connect. Then I unplug the gyro and it powers up but gets really hot after a few minutes. I have not servo controls either. Could the Flymentor be broken or is the input voltage wrong. The 450 was a 3s battery and the 500 is a 6s battery. Really don't know whats wrong.
|
05-08-2014, 05:53 PM | #4 (permalink) | |
Registered Users
Join Date: Mar 2008
|
Quote:
|
|
05-12-2014, 10:52 PM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2014
|
I ordered a new Flymentor 3D and have been installing it tonight. I can't get the helibal program to work on my Win 7 laptop but I have a program card. I got everything wired up and I set a new model heli in my Turnigy 9x Tx. Now I have done the basic setup and when I tilt the heli the swash reacts properly and the rudder reacts when the tail is rotated. What is not working is the servo control from my Tx. The only servo I can control is the rudder. I have no control over the pitch, ail, ele. I can spool up the motor and control the rudder and thats it. When I go into the display menu I have no signal being registered. I don't know what to do to correct this. I think it probably has something to do with the swash mix but according to FM manual I was supposed to turn it off, so I set all parameters to 0 on the mix. How can I get the servo control to register on my Tx? Kinda stuck here.
|
05-13-2014, 12:35 AM | #6 (permalink) |
Registered Users
Join Date: Oct 2010
|
you have a tx /rx issue protocall is signal is sent from tx to rx then flymentor sends input to the proper servo
Your gyro is compansating correctly and the tail moves im asumeing in heading hold so the flymentor is working. Are u sure your radio is bound to RX ? Did you set the radio to one servo? Sent from my SCH-I535 using Tapatalk |
05-13-2014, 08:25 AM | #7 (permalink) | |
Registered Users
Thread Starter
Join Date: Mar 2014
|
Quote:
|
|
05-13-2014, 02:04 PM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2014
|
Ok I got the servos working properly. Now I need to get the Flymentor to correct in the proper direction. Right now when I lean the heli to the right the flymentor corrects to the right and when the heli is tilted to the left it corrects to the left. I have reversed the yaw setting but it still corrects wrong.
|
05-13-2014, 04:31 PM | #9 (permalink) |
Registered Users
Join Date: Mar 2008
|
See instruction sticky at the top of the flight stabilisation section. First set the TX, then using servo reverse on the H/H controller so that the servos move correctly when you tip the heli, including the tail. Then using stick reverse on the H/H controller to set stick directions including the tail. It must be done in that order.
|
05-13-2014, 04:55 PM | #10 (permalink) |
Registered Users
Join Date: Aug 2008
|
Hi Ivor, nice to see you are still on here dishing out your excellent advice, how you doing buddy.
__________________
T-Rex600-ICE100,WR10ABEC,Scorp4025-1100+17T,Kasama head,QUK Swash CNC Tail,G-Force blocks,3152,DS760+BLS251,DX7+AR7000,FM. Blade400-CC ICE50,Scorp2221-8+12T,Sonix Head&Tail,5A BEC,HS65HB,Quark+3500G,AR7000,Align Carbon blades,TRex500 Skids,Flymentor. |
05-13-2014, 05:02 PM | #11 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2014
|
I'm sorry, but what is the H/H controller?
|
05-13-2014, 07:11 PM | #13 (permalink) |
Registered Users
Join Date: Mar 2008
|
Hi Pril, yes I look in every day or two. Would have thought that Flymentor would have been replaced by something better at a similar price by now but it has not so people are still buying them and still need help, so I do what I can. Getting old and some health problems so don't fly much any more and when I do it's useually a quad. Have a couple of them fitted with GPS, it amuses me to park it in the sky or flick a switch and watch it return to me and land. Hope you are well.
|
05-16-2014, 04:30 PM | #14 (permalink) | |
Registered Users
Join Date: Aug 2008
|
Quote:
If/when I go FBL at any point I will probably switch to IKON or MSH Brain controllers which seem reasonably priced and include a leveling facility. The highest step probably being the DJI NAZA H but the amount of flying I been doing in the last two years does not seem to justify the effort or cost. Anyway must say FM is still working well and reliably when required (like when one needs to scratch ones nose) especially for relaxed flying in confined spaces.
__________________
T-Rex600-ICE100,WR10ABEC,Scorp4025-1100+17T,Kasama head,QUK Swash CNC Tail,G-Force blocks,3152,DS760+BLS251,DX7+AR7000,FM. Blade400-CC ICE50,Scorp2221-8+12T,Sonix Head&Tail,5A BEC,HS65HB,Quark+3500G,AR7000,Align Carbon blades,TRex500 Skids,Flymentor. |
|
Tags |
flymentor 3d, setup |
Thread Tools | |
Display Modes | |
|
|