Register Now

infamousnation · 02-25-2012, 10:22 PM

I got the tarrot usb dongle because I read that it would work with the copterx fbl. I installed the driver and plugged it in and tried the software for the copterx, it wouldn;t connect. Then I tried the software for the tarrot, it wouldnt connect. Then I tried the 3rd party software that is supposed to work with all of the units. It broke my fbl unit and now it wont initialize at all. wtf

InFocus · 02-25-2012, 10:50 PM

Is the gyro fully plugged into all of the servos, esc, and rx?

InFocus · 02-25-2012, 10:51 PM

Maybe try programming it with the blinking lights, and do the 'data reset' function to restore all of the factory defaults.

infamousnation · 02-25-2012, 10:54 PM

Well I was able to fix it by plugging in the controller box and doing a model reset. Would have been up a creek without that box. Be carefull when using any 3rd party software. After I reset it, I was able to do the config using the copterx software and it worked fine.

infamousnation · 02-25-2012, 10:56 PM

It had changed all kinds of settings. The swash was set to normal mode, the servos were set to analog.

02-25-2012, 10:22 PM	#1 (permalink)
infamousnation Registered Users My HF Map location Join Date: Jan 2012	I think I bricked my cx3x1000 I got the tarrot usb dongle because I read that it would work with the copterx fbl. I installed the driver and plugged it in and tried the software for the copterx, it wouldn;t connect. Then I tried the software for the tarrot, it wouldnt connect. Then I tried the 3rd party software that is supposed to work with all of the units. It broke my fbl unit and now it wont initialize at all. wtf

02-25-2012, 10:50 PM	#2 (permalink)
InFocus Registered Users Join Date: Jun 2011	Is the gyro fully plugged into all of the servos, esc, and rx? __________________ Current fleet is getting smaller. Blackout Mini-H, WarpQuad 230, Blade 200qx, Nano QX, UM F-27q Stryker, UM P51 Mustang, F4F Wildcat, DX6 radio. Previous fleet: mcpx, 300x, 350qx,450x, qav400, DX7s

02-25-2012, 10:51 PM	#3 (permalink)
InFocus Registered Users Join Date: Jun 2011	Maybe try programming it with the blinking lights, and do the 'data reset' function to restore all of the factory defaults. __________________ Current fleet is getting smaller. Blackout Mini-H, WarpQuad 230, Blade 200qx, Nano QX, UM F-27q Stryker, UM P51 Mustang, F4F Wildcat, DX6 radio. Previous fleet: mcpx, 300x, 350qx,450x, qav400, DX7s

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-25-2012, 10:54 PM	#4 (permalink)
infamousnation Registered Users Thread Starter My HF Map location Join Date: Jan 2012	Well I was able to fix it by plugging in the controller box and doing a model reset. Would have been up a creek without that box. Be carefull when using any 3rd party software. After I reset it, I was able to do the config using the copterx software and it worked fine.

02-25-2012, 10:56 PM	#5 (permalink)
infamousnation Registered Users Thread Starter My HF Map location Join Date: Jan 2012	It had changed all kinds of settings. The swash was set to normal mode, the servos were set to analog.

Register Now

Log-in