 |
START HERE |
|
| Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
|
|
|
Unregistered
|
||||||
| 600 Class Electric Helicopters 600 Class Electric Helicopters manufactured by Align, Tarot, SYMA, Airhog, Chaos, HK and similar. |
|
|
 |
|
|
LinkBack | Thread Tools | Display Modes |
10-23-2014, 08:42 AM
|
#1 (permalink) |
|
Registered Users
Join Date: Oct 2014
|
may fit this engine?
Hello everyone. wondering if you can fit the engine bl600mx since the bl600xl not produce it anymore. so I wanted to put the engine bl600mx this engine I can put safely or should I make some changes since my pinion has 10 teeth?
|
|
|
| Sponsored Links | |||
|
Advertisement |
|
||
|
10-27-2014, 10:32 AM
|
#2 (permalink) |
|
Registered Users
Join Date: Jun 2010
|
They are completely different motors. One is for a 6s and the other is for a 12s. Also you would have to switch to a HV ESC as well.
__________________
Trex 700L Ikon 2 / Trex 700L Ikon V. 2 / SAB Goblin 500 Sport Ikon 2 / HD Cell 500 Ikon 2 It isn't about if, it is about when! |
|
|
|
|
10-28-2014, 09:10 AM
|
#3 (permalink) |
|
Registered Users
Thread Starter
Join Date: Oct 2014
|
OK. but I can mount this engine bl600mx the t-rex 600cf? I have to make changes?
|
|
|
|
|
10-28-2014, 09:18 AM
|
#4 (permalink) |
|
Registered Users
Thread Starter
Join Date: Oct 2014
|
OK. but I can mount this engine bl600mx the t-rex 600cf? I have to make changes?
|
|
|
|
|
10-31-2014, 11:59 PM
|
#5 (permalink) |
|
Registered Users
Join Date: Jan 2014
|
I have the CF model and just did a BIG REBUILD and update...
YES the 600MX fits the cf frame. I up dated to the 112T slant gear and the DFC/PRO one-way bearing and hub. I'm running a 12T pinion with my 600mx 510KV motor. You will have to find out your main gear tooth count and what KV your 600mx is to find out if you can run that pinion. A 510kv needs 12s.. I should be around 1950 to 2050 gov head speed give or take a little. This should give me some head room for the gov to work well.
__________________
KDS Agile 6.4 Proto-Type 750MX 12s with an Ikon / KDS Agile 7.2 / Tarot-Align 600CF-FBL Robird G31 12S / The First X3-385 FROM AUTO-CAD to DIRT NAP in 10 SECONDS ! |
|
|
|
|
11-01-2014, 02:53 AM
|
#6 (permalink) |
|
Registered Users
Join Date: Jun 2010
|
Depends on your frame. The older style frame had to be modified to fit the bigger motor. The newer aftermarket frames for the CF are cut out to fit the bigger motors.
__________________
Trex 700L Ikon 2 / Trex 700L Ikon V. 2 / SAB Goblin 500 Sport Ikon 2 / HD Cell 500 Ikon 2 It isn't about if, it is about when! |
|
|
|
|
11-03-2014, 09:55 PM
|
#7 (permalink) |
|
Registered Users
Join Date: Jan 2010
|
There are two versions of the BL600MX -
510kv (12S) and 1220kv (6S). If the 1220KV motor is your choice, you are still looking at the size difference. The two versions of the BL600MX are the same size, but the are quite a bit wider than the BL600XL. Additionally, the BL600MX uses a 6mm spindle vs. 5mm for the XL. BL600XL: Dimension:spindle 5x65x43.3mm (1650kv) BL600MX: Dimension: spindle 6x45x59mm (1220kv) I would start by measuring the distance from the inside frame-to-frame. Then, measure the distance from you existing BL600XL to the servos. I would suggest the frame-to-frame must be 60mm and the distance from the BL600XL can to the closest servo should be 8mm Then you will need a new pinion to fit the 6mm spindle on the MX. And, you may have to use a 11T pinion to compensate for the slower RPM of the MX. |
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
