START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Walkera Helicopters Walkera Helicopter Support |
|
LinkBack | Thread Tools | Display Modes |
12-20-2012, 02:08 PM | #1 (permalink) |
Registered Users
Join Date: Nov 2012
|
Walkera V450D03 tx settings
Need some help with tx settings for DEVO-10. So far, I'm happy with the factory settings. It starts to spin up at 0% throttle. I would like to fix this, but not sure what settings is best. I want to start with beginner settings. Any advice?
|
Sponsored Links | |||
Advertisement |
|
12-22-2012, 10:10 PM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Nov 2012
|
My throttle curve value for normal normal throttle:
PL = 0.0% P1 = INH P2 - INH PM = 50% P3 = INH P4 = INH PH = 100.0% |
12-23-2012, 10:40 AM | #4 (permalink) |
Join Date: Jun 2008
|
I sent shawnr1 a PM and said to make sure the throttle trim was all the way down
and to check that the throttle curve value was set to "0" on PL. Shawn, also check the throttle sub trim and make sure it is set to "0". And check that the left and right trim switches next to "Gear" and Mix" are centered. Click them "+" and "-" and listen to the beeps. You will hear a high beep when you reach center position. I would also do a Stick Calibration which is in the Main Menu - System Menu. Your throttle stick may be off Calibration. Other than what I have posted I can't see any Tx setting that would cause it to start to spin up at 0% throttle. There is a throttle bug in the firmware for the V120D02SV2 that would not allow the blades to stop spinning after hitting throttle hold. This bug has been fixed in a new firmware release. Your heli may have a throttle bug also. I just checked with Walkera and there is no firmware update for the V450D03. I would see if anyone who has the V450D03 has the same problem you are having also. If so let me know and I will inform Walkera about this. Tom |
12-23-2012, 01:43 PM | #5 (permalink) | |
Registered Users
Join Date: May 2010
|
Quote:
|
|
12-24-2012, 12:57 AM | #9 (permalink) |
Registered Users
Join Date: May 2010
|
Not at startup did you setup throttle hold? It needs to activate for that heli. All the trim set to zero on tx, Once I started up to fly it would keep spinning when I would come back to land from flying.
|
12-24-2012, 08:15 AM | #10 (permalink) |
Join Date: Jun 2008
|
Throttle hold on the Devo 10.
Throttle Hold - Hold Status- Active Hold Position = 0.0 % You can also try Hold Position = -15% if the blades still spin. Tom |
12-25-2012, 01:26 AM | #11 (permalink) | |
Join Date: Sep 2012
|
I just found this... Hope it helps....
Quote:
|
|
12-25-2012, 10:43 PM | #12 (permalink) |
Registered Users
Thread Starter
Join Date: Nov 2012
|
Thanks for all the replies. I love this heli. Had a chance to take it outside today and hover it for a minute. It is very stable. The -15% hold position worked. However, it still spins at 0% throttle, which I can let go for now.
If anyone else come up with some more info on this heli please post. Thx! |
12-25-2012, 11:47 PM | #13 (permalink) |
Join Date: Sep 2012
|
THis is how you do the big helis... Might work for this model...
Go into the Travel Adjustment menu and set high and low to 25% Remove blades..... Plug in heli... Throttle stick all the way in up position.... Set high travel adjustment until it beeps and then go a couple of more (might go over 100%)... Throttle stick all the way down... Set low travel adjustment until it beeps and then go a couple of more (might go over 100%)...... Unplug heli Turn off transmitter Plug in heli Turn on TX with throttle in lowest position Try this and let me know.... |
12-26-2012, 12:07 AM | #14 (permalink) |
Join Date: Sep 2012
|
Another thing to try is select a new model and start from scratch (DO NOT copy old settings) and program according to manual... Here is the link....
http://walkera.com/cn/upload/explain/V450D03_expe.pdf |
01-08-2013, 09:09 PM | #15 (permalink) | |
Registered Users
Join Date: Jan 2009
|
Quote:
|
|
01-08-2013, 10:02 PM | #16 (permalink) |
Registered Users
Thread Starter
Join Date: Nov 2012
|
Try this link: http://www.devention.com:82/cn/uploa...50D03_expe.pdf
|
01-19-2013, 08:58 PM | #17 (permalink) |
Registered Users
Join Date: Jan 2009
|
Negative...that doesn't work either.
|
01-19-2013, 09:44 PM | #18 (permalink) |
Registered Users
Join Date: Dec 2011
|
sounds like the esc needs to be recalibrated to know where throttle 0, you probably did a bind while the throttle was a hair up and now it thinks thats 0 throttle.
|
02-28-2013, 04:09 AM | #19 (permalink) |
Registered Users
Join Date: Feb 2013
|
I also have the DEVO-10 and the main blade still spin at 0 throttle.
Has anybody come up with any other ideas? Oh by the way first time posting on this forum |
Thread Tools | |
Display Modes | |
|
|