Register Now

tbear125 · 03-21-2012, 07:32 PM

Tried getting my 450 se up in the air today, but can't seem to keep it from spinning to the left. I did notice that it looks like the main shaft has a slight wobble. Was wondering if any one has any ideas as to what could be the problem?

newbheliusr · 03-21-2012, 07:46 PM

Sounds like you need to reverse the gyro. Not in the Tx but in the gyro.

What gyro is it?

Rex

Sent from my iPhone using Tapatalk

czynot · 03-21-2012, 07:46 PM

1) rudder channel reversed?
2) gain too low?
3) tail blade backward?

tbear125 · 03-22-2012, 12:09 PM

I'm running a gy 401 with a futaba 9650 on the tail.

newbheliusr · 03-22-2012, 01:08 PM

This is really easy to figure out if it's gyro correction direction or rudder stick direction

To check gyro correction
Power on Tx, Power on heli. With the tail facing you move the tail to the right. The leading edge of the tail blades should point left. If they do not, reverse the gyro

Rudder stick direction:
Power on Tx, Power on Heli. Move the rudder stick to the right (this is known as flying those nose for this reason) The nose should move right, tail left. so when you push the rudder stick on the Tx to the right, the tail should go left. So the leading edge of the tail blades should point left.

Easy.

If you have any problems PM me and I'll try to help.

Also make sure your tail blades are spinning the right direction. Most often it's counter clockwise when looking at the side the tail blades are on. Main blades spin clockwise, tail blades CCW. The tail blades should move up into the down wash of the main rotors.

Rex

GreyEyes · 03-22-2012, 05:01 PM

Quote:

Originally Posted by newbheliusr

To check gyro correction
Power on Tx, Power on heli. With the tail facing you move the tail to the left. The leading edge of the tail blades should point left. If they do not, reverse the gyro

newbheliusr · 03-22-2012, 05:20 PM

Darn it, I fixed it. I apologize. I was at work and kinda busy when I did that. Thank you for catching it. I feel so dumb.

Quote:

Originally Posted by GreyEyes

GreyEyes · 03-22-2012, 05:44 PM

LOL, I knew you knew better, especially since you had it right in the second part of the post

wanderer56 · 03-22-2012, 06:10 PM

newbheliusr-"Put down the mouse and move away from the pc slowly!"

newbheliusr · 03-22-2012, 06:25 PM

I even work on comps for a living. Man I gotta watch out. I could have hurt someone. Thank god you caught it. Hopefully I can fly better than I give advice.

Sent from my iPhone using Tapatalk

03-21-2012, 07:32 PM	#1 (permalink)
tbear125 Registered Users Join Date: Feb 2012	Trex 450 se v2 Tail spinning. Tried getting my 450 se up in the air today, but can't seem to keep it from spinning to the left. I did notice that it looks like the main shaft has a slight wobble. Was wondering if any one has any ideas as to what could be the problem?

03-21-2012, 07:46 PM	#2 (permalink)
newbheliusr Registered Users Join Date: Apr 2011	Sounds like you need to reverse the gyro. Not in the Tx but in the gyro. What gyro is it? Rex Sent from my iPhone using Tapatalk __________________ Heli's I have: Goblin 500 (Vbar Neo), Gaui X5(Vbar Neo), X7(Vbar Neo), Innova 600 Night heli (Vbar Neo Vbar Vcontrol I'm the not so newbheliusr as I have been here a while. But I like this name.

03-22-2012, 12:09 PM	#4 (permalink)
tbear125 Registered Users Thread Starter Join Date: Feb 2012	450 se tail spinning I'm running a gy 401 with a futaba 9650 on the tail.

03-22-2012, 01:08 PM	#5 (permalink)
newbheliusr Registered Users Join Date: Apr 2011	This is really easy to figure out if it's gyro correction direction or rudder stick direction To check gyro correction Power on Tx, Power on heli. With the tail facing you move the tail to the right. The leading edge of the tail blades should point left. If they do not, reverse the gyro Rudder stick direction: Power on Tx, Power on Heli. Move the rudder stick to the right (this is known as flying those nose for this reason) The nose should move right, tail left. so when you push the rudder stick on the Tx to the right, the tail should go left. So the leading edge of the tail blades should point left. Easy. If you have any problems PM me and I'll try to help. Also make sure your tail blades are spinning the right direction. Most often it's counter clockwise when looking at the side the tail blades are on. Main blades spin clockwise, tail blades CCW. The tail blades should move up into the down wash of the main rotors. Rex Last edited by newbheliusr; 03-22-2012 at 05:19 PM..

03-22-2012, 05:44 PM	#8 (permalink)
GreyEyes Registered Users Join Date: Nov 2011	LOL, I knew you knew better, especially since you had it right in the second part of the post __________________ Trex 450 Pro V2 Trex 450 Sport V2 Esky Belt CPX Blade mCP X

03-21-2012, 07:46 PM	#3 (permalink)
czynot Registered Users Join Date: Aug 2011	1) rudder channel reversed? 2) gain too low? 3) tail blade backward?

03-22-2012, 06:10 PM	#9 (permalink)
wanderer56 Registered Users My HF Map location Join Date: Oct 2009	newbheliusr-"Put down the mouse and move away from the pc slowly!" __________________ Trex 500-3226-1600, 14T, Koby 90LV, HS-5245MG, DS655, AR7200BX, DFC Trex 450 Sport-2221-8, 15T, CC Edge 50 Lite, HS-5065MG, HSG-5084MG, AR7200BX, DFC DX8

03-22-2012, 06:25 PM	#10 (permalink)
newbheliusr Registered Users Join Date: Apr 2011	I even work on comps for a living. Man I gotta watch out. I could have hurt someone. Thank god you caught it. Hopefully I can fly better than I give advice. Sent from my iPhone using Tapatalk __________________ Heli's I have: Goblin 500 (Vbar Neo), Gaui X5(Vbar Neo), X7(Vbar Neo), Innova 600 Night heli (Vbar Neo Vbar Vcontrol I'm the not so newbheliusr as I have been here a while. But I like this name.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in