START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
05-25-2012, 02:56 PM | #1 (permalink) |
Registered Users
Join Date: Jun 2011
|
Help!! Esc Calibration and Gov settings
I'm new to vbar and have watch the video's several times. I have set it up according to video 20. In normal the heli will not spool up until I get pass half stick. after spool up i go back to half stick it starts slowing down. then its slow to spool back up. is this normal?
Here is my setup CC Ice 100 V3.27 Hyperion sensor Scorpin 4025-1100 12t pinion 129t main Tx throttle is 104/79 for 100/100 on vbar Here is the file. |
Sponsored Links | |||
Advertisement |
|
05-25-2012, 09:06 PM | #2 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2011
|
come on 40 views and no suggestions!
|
05-25-2012, 09:27 PM | #3 (permalink) |
Registered Users
Join Date: Feb 2009
|
Mr Mel shows in one of the video on spool up u have to go past 50 for vbar to spool up..if u see it in video its clearly pointed out,if not than u been watching the wrong one....i run Kontronic so i dont use the vbar gov....if u see it ramp up fine than u on the right track..
|
05-26-2012, 12:41 AM | #4 (permalink) | |
Registered Users
Join Date: Jan 2011
|
Quote:
You should not be adjusting the values in the tx to get 100/100 values in vbar gov tab. Only for calibrating endpoints for esc and vbar transm tab. If you watched the right video, after you calibrate the esc endpoints, then transm tab, you will go to the gov 1 select your channels. gov 2 you need to flip on throttle hold, put your throttle to mid stick, and then flip in and out of throttle hold untill you get NO DELAY.(this means moving the slider one point at a time to get no delay from the time you flip out of throttle hold and the motor starting. that is how you calibrate low end throttle. ) the slider values will never be 100/100 in gov 2 tab.
__________________
Vcontrol-Vbar-Nitro Gov Whip Nitro 105 Awaiting V2 Conversion Synergy N7 105 *Perspective is key* |
|
05-26-2012, 08:47 AM | #5 (permalink) | |
Registered Users
Thread Starter
Join Date: Jun 2011
|
Quote:
I do have another question. On my idle up 2. I have flat 100% throttle curve. In the Gov. tad I have 2150 set as max. It shows 2670 as requested in IU2. Shouldn't it only go to 2150 max? |
|
05-26-2012, 07:35 PM | #6 (permalink) | |
Registered Users
Join Date: Jan 2011
|
Quote:
let me know(PM ME) if you have any other problems as i just set the gov up and it is fresh in my mind
__________________
Vcontrol-Vbar-Nitro Gov Whip Nitro 105 Awaiting V2 Conversion Synergy N7 105 *Perspective is key* |
|
05-27-2012, 11:44 AM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Jun 2011
|
My gear ratio was wrong. Test flew it today! Thanks for the help!
|
05-27-2012, 09:59 PM | #8 (permalink) |
Registered Users
Join Date: Jan 2011
|
No problem. I like to pass on my knowledge. I was taught by one of the original owners of a vbar when everyone else had a flybar and fbl was "cheating"
__________________
Vcontrol-Vbar-Nitro Gov Whip Nitro 105 Awaiting V2 Conversion Synergy N7 105 *Perspective is key* |
04-11-2016, 10:07 PM | #9 (permalink) | |||
Registered Users
Join Date: Oct 2012
|
Hi I have the same issue as the OP. No spoolup in normal mode until midstick. I have it programmed just as it shows in episode 20. 100/100 in vbar tx tab, and 110/46 in vbar gov II tab. I know the high point is low so the resolution will be poor but why should that affect the bottom half of the normal mode? The soft start seems to be working good but I don't have blades for this heli to test it properly.
Quote:
EDIT- I reset the esc endpoints, now the gov II tab numbers are 110/88, but it still has the issue. As far as I can tell, the vid i have linked in this post is the most up to date one.
__________________
R/C Outlaw (and proud of it) since February 20, 2016 Last edited by Eric T; 04-12-2016 at 07:54 AM.. |
|||
Thread Tools | |
Display Modes | |
|
|