Radio ATV and quark

devens · 03-01-2010, 12:28 PM

I am trying to program my quark gyro and I am stuck at the servo travel. The manual says to be in set-up mode 2 or 3 for low and high endpoint adjustments respectivly. The manual then states to move the rudder stick to prevent binding and press set-up button to store. When I get to step 2 in set-up nothing happens when I move my rudder stick. As a matter of fact my tail doesn't move in any of the 3 set-up steps.

I don't think the servo/gyro is bad I just think I don't understand the manual and someone is going to have to point me in the righ direction.

ty

D

kazager · 03-01-2010, 02:58 PM

I can't explain it any better than the manual. I haven't heard anyone complain of the way the instructions are written. I've got 3 Quarks, and I have had to refer to the manual every time. Is there a Finless video on the Quark that might help you.

kazager · 03-01-2010, 03:00 PM

http://www.helifreak.com/showthread.php?t=176987

devens · 03-01-2010, 03:48 PM

Quote:

Originally Posted by kazager

http://www.helifreak.com/showthread.php?t=176987

I did a search posted. All I got was the ds760 review. I figured they were similar but wasn't going to assume they were. Sorry for asking

devens · 03-01-2010, 03:49 PM

Quote:

Originally Posted by kazager

I can't explain it any better than the manual. I haven't heard anyone complain of the way the instructions are written. I've got 3 Quarks, and I have had to refer to the manual every time. Is there a Finless video on the Quark that might help you.

congrats

kazager · 03-01-2010, 07:41 PM

I'm trying to help, if you can't take a little ribbing, sorry.

nexgen · 03-02-2010, 01:38 PM

does the servo move when you move the rudder under normal operation (not in setup mode)?

03-01-2010, 12:28 PM	#1
devens Registered Users Join Date: Jun 2009 Location: Illinois	Radio ATV and quark I am trying to program my quark gyro and I am stuck at the servo travel. The manual says to be in set-up mode 2 or 3 for low and high endpoint adjustments respectivly. The manual then states to move the rudder stick to prevent binding and press set-up button to store. When I get to step 2 in set-up nothing happens when I move my rudder stick. As a matter of fact my tail doesn't move in any of the 3 set-up steps. I don't think the servo/gyro is bad I just think I don't understand the manual and someone is going to have to point me in the righ direction. ty D Last edited by devens; 03-01-2010 at 03:47 PM..

03-01-2010, 03:00 PM	#3
kazager Registered Users Join Date: Apr 2009 Location: MD, USA	Search...Priceless http://www.helifreak.com/showthread.php?t=176987

03-02-2010, 01:38 PM	#7
nexgen Registered Users My HF Map location Join Date: May 2008 Location: Brainerd, MN	does the servo move when you move the rudder under normal operation (not in setup mode)? __________________ GAUI Field RepbeastX│Team Empire Hobby *Gaui 200 •Gaui 550 •Gaui X5* *BeastX Castle Scorpion Hyperion Spektrum JR* To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-01-2010, 02:58 PM	#2
kazager Registered Users Join Date: Apr 2009 Location: MD, USA	I can't explain it any better than the manual. I haven't heard anyone complain of the way the instructions are written. I've got 3 Quarks, and I have had to refer to the manual every time. Is there a Finless video on the Quark that might help you.

03-01-2010, 07:41 PM	#6
kazager Registered Users Join Date: Apr 2009 Location: MD, USA	I'm trying to help, if you can't take a little ribbing, sorry.