Custom Heli Parts 700E

darkfa8 · 01-11-2011, 08:12 PM

Features:
- Custom Heli Parts Trex 700N to Electric conversion kit airframe
- Align Trex 700N Flybar rotor head, completely rebuilt,all bearings greased.
- Align full metal tail
- Frames have built in pinion support
- 3 battery trays
- adjustable motor mount
- elevator output shaft bearing supported
- Align mod-1 115t main gear (version 1, FAD-heli gear pictured but sold)
- Stealth 105mm carbon tail blades
- carbon fiber reinforced bell-crank linkages
- Fusuno unpainted cabin
- CHP horizontal and vertical 3D tail fins
- head button hole in rotor head yoke is stripped.
- Airframe has 4 flights, no crashes.

So, what's better about this compared to the stock Align 700E?
- Lighter construction (depending on equipment used, 9lbs or less RTF with batteries)
- built-in PEM nuts for servos
- Alignment holes for servo linkage setup
- simplified design = easy to work on/repair
- built-in adjustable motor mount with pinion support
- low parts count

Story on the Nitro parts:
There are about 20 flights on the nitro parts. I bought a Trex 700NSP, pulled the parts I needed, took everything apart, cleaned, greased all bearings with The Greaser, reassembled and installed into the new, electric airframe, put 4 flights on it since it was assembled.

NO ELECTRONICS or MAIN ROTOR BLADES INCLUDED!

$375 shipped in the USA. Paypal accepted if you pay fees.

If you want to go flybarless, I'll pull the flybar head and knock off some money, so total shipped would be $325

darkfa8 · 01-13-2011, 10:02 AM

darkfa8 · 01-14-2011, 03:51 PM

darkfa8 · 01-16-2011, 09:51 AM

darkfa8 · 01-17-2011, 07:15 AM

price lowered!

jongam0 · 01-17-2011, 08:38 PM

PM sent

darkfa8 · 01-18-2011, 09:31 AM

reply sent.

helimach · 01-18-2011, 04:32 PM

Hi, I am quite interested in your 700E for sale.

I would take it without the flybared head, as I would go flybarless. So I would be near your lower price offer.

Do you still have it for sale, do you take PayPal?

Why are you selling after only four flights?

HeliMach

darkfa8 · 01-18-2011, 04:41 PM

It is still available.

I would accept paypal if you paid the fees.

I am selling because I cannot afford to crash this model.

nwcudaman · 01-18-2011, 06:21 PM

Will someone PLEASE buy this so I can quit banging my head on the table, crying out loud!!!

darkfa8 · 01-18-2011, 06:42 PM

don't bang your head on a table, just fork over some cash and it'll be yours

nwcudaman · 01-18-2011, 07:21 PM

I'm looking at the market for what the going rate is for my kid....But don't tell my wife!!!

darkfa8 · 01-21-2011, 07:42 AM

still available

darkfa8 · 01-23-2011, 10:25 AM

darkfa8 · 01-23-2011, 02:29 PM

pictures updated

darkfa8 · 01-24-2011, 09:23 AM

still available!

darkfa8 · 01-26-2011, 11:23 AM

selling on RR

01-11-2011, 08:12 PM	#1
darkfa8 Registered Users Join Date: May 2005 Location: Brick, NJ, USA	Custom Heli Parts 700E Features: - Custom Heli Parts Trex 700N to Electric conversion kit airframe - Align Trex 700N Flybar rotor head, completely rebuilt,all bearings greased. - Align full metal tail - Frames have built in pinion support - 3 battery trays - adjustable motor mount - elevator output shaft bearing supported - Align mod-1 115t main gear (version 1, FAD-heli gear pictured but sold) - Stealth 105mm carbon tail blades - carbon fiber reinforced bell-crank linkages - Fusuno unpainted cabin - CHP horizontal and vertical 3D tail fins - head button hole in rotor head yoke is stripped. - Airframe has 4 flights, no crashes. So, what's better about this compared to the stock Align 700E? - Lighter construction (depending on equipment used, 9lbs or less RTF with batteries) - built-in PEM nuts for servos - Alignment holes for servo linkage setup - simplified design = easy to work on/repair - built-in adjustable motor mount with pinion support - low parts count Story on the Nitro parts: There are about 20 flights on the nitro parts. I bought a Trex 700NSP, pulled the parts I needed, took everything apart, cleaned, greased all bearings with The Greaser, reassembled and installed into the new, electric airframe, put 4 flights on it since it was assembled. NO ELECTRONICS or MAIN ROTOR BLADES INCLUDED! $375 shipped in the USA. Paypal accepted if you pay fees. If you want to go flybarless, I'll pull the flybar head and knock off some money, so total shipped would be $325 __________________ - Dan G. - - Team HobbyHut - Last edited by darkfa8; 01-23-2011 at 02:29 PM..

01-13-2011, 10:02 AM	#2
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	ttt __________________ - Dan G. - - Team HobbyHut -

01-14-2011, 03:51 PM	#3
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	ttt __________________ - Dan G. - - Team HobbyHut -

01-16-2011, 09:51 AM	#4
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	ttt __________________ - Dan G. - - Team HobbyHut -

01-17-2011, 07:15 AM	#5
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	price lowered! __________________ - Dan G. - - Team HobbyHut -

01-17-2011, 08:38 PM	#6
jongam0 Registered Users Join Date: Mar 2008	PM sent

01-18-2011, 09:31 AM	#7
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	reply sent. __________________ - Dan G. - - Team HobbyHut -

01-18-2011, 04:32 PM	#8
helimach Registered Users Join Date: May 2008 Location: Portland, Maine	700E for Sale Hi, I am quite interested in your 700E for sale. I would take it without the flybared head, as I would go flybarless. So I would be near your lower price offer. Do you still have it for sale, do you take PayPal? Why are you selling after only four flights? HeliMach

01-18-2011, 04:41 PM	#9
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	It is still available. I would accept paypal if you paid the fees. I am selling because I cannot afford to crash this model. __________________ - Dan G. - - Team HobbyHut -

01-18-2011, 06:21 PM	#10
nwcudaman Registered Users My HF Map location Join Date: Mar 2009 Location: Boring Oregon	Will someone PLEASE buy this so I can quit banging my head on the table, crying out loud!!! __________________ President Field Of Screams Helicopter Club Normally it starts with...."Watch This" Trex 550E FBL (Buzz) Walkera V120D02S V2 Devo 8S, Sr 120, MCX, MCPX, TREX 250, DJI F330, DJI F450, Walkera Ladybird, yadda yadda..

01-18-2011, 06:42 PM	#11
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	don't bang your head on a table, just fork over some cash and it'll be yours __________________ - Dan G. - - Team HobbyHut -

01-18-2011, 07:21 PM	#12
nwcudaman Registered Users My HF Map location Join Date: Mar 2009 Location: Boring Oregon	I'm looking at the market for what the going rate is for my kid....But don't tell my wife!!! __________________ President Field Of Screams Helicopter Club Normally it starts with...."Watch This" Trex 550E FBL (Buzz) Walkera V120D02S V2 Devo 8S, Sr 120, MCX, MCPX, TREX 250, DJI F330, DJI F450, Walkera Ladybird, yadda yadda..

01-21-2011, 07:42 AM	#13
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	still available __________________ - Dan G. - - Team HobbyHut -

01-23-2011, 10:25 AM	#14
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	ttt __________________ - Dan G. - - Team HobbyHut -

01-23-2011, 02:29 PM	#15
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	pictures updated __________________ - Dan G. - - Team HobbyHut -

01-24-2011, 09:23 AM	#16
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	still available! __________________ - Dan G. - - Team HobbyHut -

01-26-2011, 11:23 AM	#17
darkfa8 Registered Users Thread Starter Join Date: May 2005 Location: Brick, NJ, USA	selling on RR __________________ - Dan G. - - Team HobbyHut -

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode