Register Now

Dlobo · 03-05-2013, 10:01 PM

I am attemping to build a HK 450 TT FBL and I am almost finished.

I can not find any diagram, picture, youtube video or living being that can tell me in plain English how to connect a "CX-3X1000" Gyro to a Flysky 9 channel receiver.

The receiver booklet says hook up your Futaba servo number whatever to x channel. That would be great if I had Futaba servos with numbers on them.

What I am looking for is someone to tell me plug the Elevator servo wires into this channel and pug the black-red-black Gryo wire into that channel on the receiver, and so on.

What I know is that how I have it plugged in now is not perfect. When I hit full collective it goes up wonky so something is not plugged in correctly but I don't know what. Rudder looks good and responds as I think it should. I even played around with JZ's Gyro program but didn't save anything because it seemed pointless.

Thanks for reading.

ps. I am so new that saying things like the servo on left would be very helpful as I have nothing but a 4 ch FP and a MCPX to reference in the garage. lol

satgod · 03-05-2013, 10:34 PM

just connect to the corresponding connection on the frysky
ussually its rudder gyro gain of of course what ever channels are you aliron, elevator

sounds like your over thinking this one

just back up and think about it for a second

Dlobo · 03-05-2013, 10:43 PM

From the CX Gyro there are only two sets of wires, one at the each end of the physical box which split into 5 plugs that go to the receiver. No way to match numbers that I can think of..

Dlobo · 03-11-2013, 11:11 PM

Satgod, I did rethink it.
I sat back and drew my own diagram of the connections.
I am a 'Have to see it' type of person.
I had the Aileron and Pitch wires reversed which caused everything to go wonky.

I hope I never have to do it again because I am looking at where I left my diagram and all I see is the kids parent teacher conference schedule and a jury summons.
wtf happened to my beautiful drawing?

03-05-2013, 10:01 PM	#1 (permalink)
Dlobo Registered Users Join Date: Jan 2013	CX3x1000 to FS-R9B Confg I am attemping to build a HK 450 TT FBL and I am almost finished. I can not find any diagram, picture, youtube video or living being that can tell me in plain English how to connect a "CX-3X1000" Gyro to a Flysky 9 channel receiver. The receiver booklet says hook up your Futaba servo number whatever to x channel. That would be great if I had Futaba servos with numbers on them. What I am looking for is someone to tell me plug the Elevator servo wires into this channel and pug the black-red-black Gryo wire into that channel on the receiver, and so on. What I know is that how I have it plugged in now is not perfect. When I hit full collective it goes up wonky so something is not plugged in correctly but I don't know what. Rudder looks good and responds as I think it should. I even played around with JZ's Gyro program but didn't save anything because it seemed pointless. Thanks for reading. ps. I am so new that saying things like the servo on left would be very helpful as I have nothing but a 4 ch FP and a MCPX to reference in the garage. lol

03-05-2013, 10:34 PM	#2 (permalink)
satgod Registered Users My HF Map location Join Date: Apr 2011	just connect to the corresponding connection on the frysky ussually its rudder gyro gain of of course what ever channels are you aliron, elevator sounds like your over thinking this one just back up and think about it for a second __________________ 4 x Rush 750/stretched V-bar KDE 700XF-495 HV servos Greys reactor CC 160-HV Trex 600EFL V2 V-Bar ds610 ds650 CC bec/pro Scorpion 130a HV KDE 600XF-530 450L KDE 1750 cc50 4xDS215MG k-bar X-8 FPV Wing, TBS Discovery FPV, TBS Caipirinha FPV

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-05-2013, 10:43 PM	#3 (permalink)
Dlobo Registered Users Thread Starter Join Date: Jan 2013	From the CX Gyro there are only two sets of wires, one at the each end of the physical box which split into 5 plugs that go to the receiver. No way to match numbers that I can think of..

03-11-2013, 11:11 PM	#4 (permalink)
Dlobo Registered Users Thread Starter Join Date: Jan 2013	Satgod, I did rethink it. I sat back and drew my own diagram of the connections. I am a 'Have to see it' type of person. I had the Aileron and Pitch wires reversed which caused everything to go wonky. I hope I never have to do it again because I am looking at where I left my diagram and all I see is the kids parent teacher conference schedule and a jury summons. wtf happened to my beautiful drawing?

Register Now

Log-in