Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > Blogs


Old

Twinn Rexx FBL upgrade

Posted 08-21-2012 at 11:32 PM by jolyboy
Updated 08-23-2012 at 04:22 AM by jolyboy

The new flybarless module finally arrived yesterday - a new MSH Brain. I spent the last few hours setting it up, and it looks pretty promising so far.

Also, I have the new flybarless heads installed. Below is a picture of how the tandem looks with one of the 450DFC heads installed.



The initial flight was scary due to major pitch oscillations, which were expected. After fiddling...
Attached Thumbnails
Click image for larger version

Name:	SNV15458.JPG
Views:	2167
Size:	236.8 KB
ID:	945  
jolyboy's Avatar
Registered Users
Posted in Uncategorized
Views 2977 Comments 0 jolyboy is offline
Old

Flybarless Twinn Rexx

Posted 08-01-2012 at 07:00 AM by jolyboy

I'm now in the process of upgrading my twinn rexx to flybarless . Reasons for doing so are:
  1. Simplified set-up
  2. Mechanically better (less "slop")
  3. Lighter
  4. Better for use with autopilots in the future
  5. More crash resistent
  6. Ability to run an ultra-low headpeed for FPV flying (no flybar requiring inertia to operate)

I'll be running 2 x Tarot 450DFC heads, with one Tarot ZYX-S flybarless unit fed into a TH-2 tandem mixer. The tandem mixer settings will be the...
jolyboy's Avatar
Registered Users
Posted in Uncategorized
Views 1567 Comments 0 jolyboy is offline
Old

First Flyable Config

Posted 07-21-2012 at 06:52 AM by jolyboy

This is the first flyable configuration I did. I have done revised versions of this for better CoG, but now I'm in the process of upgrading to flybarless due to the horrible quality of the blue rotors (bearings jamming, screws breaking ). The new rotors will be Tarot 450DFC heads, which allow better pitch range than the flybarred heads and much less slop.

Click image for larger version

Name:	SNV15414.JPG
Views:	1453
Size:	254.7 KB
ID:	933

Click image for larger version

Name:	SNV15415.JPG
Views:	461
Size:	223.6 KB
ID:	934

Click image for larger version

Name:	SNV15418.jpg
Views:	404
Size:	51.3 KB
ID:	935

Click image for larger version

Name:	SNV15419.jpg
Views:	482
Size:	49.4 KB
ID:	936...
jolyboy's Avatar
Registered Users
Posted in Uncategorized
Views 1303 Comments 0 jolyboy is offline
Old

Trial fit of components

Posted 07-06-2012 at 09:18 PM by jolyboy

Click image for larger version

Name:	SNV15405_1.jpg
Views:	374
Size:	354.9 KB
ID:	924

Click image for larger version

Name:	SNV15406_1.jpg
Views:	341
Size:	54.4 KB
ID:	925

Click image for larger version

Name:	SNV15399_1.jpg
Views:	349
Size:	334.0 KB
ID:	926

Click image for larger version

Name:	SNV15400_1.jpg
Views:	333
Size:	328.1 KB
ID:	927

Click image for larger version

Name:	SNV15403_1.jpg
Views:	334
Size:	268.9 KB
ID:	928

Click image for larger version

Name:	SNV15404_1.jpg
Views:	330
Size:	299.2 KB
ID:	929
jolyboy's Avatar
Registered Users
Posted in Uncategorized
Views 1349 Comments 0 jolyboy is offline
Old

Modified Twinn Rexx with rear-mounted motor

Posted 07-04-2012 at 06:59 PM by jolyboy
Updated 07-04-2012 at 07:22 PM by jolyboy (Add photos)

This blog is to keep track of my progress on the Twinn Rexx build I undertook a few months ago. There have been many issues from the lack of the availability of parts, so I have modified the design as a work-around. The only part sourced from Tech-MP is the TH-2 tandem controller, since all other parts are no longer available.

So far, the chassis has been the most challenging part of the build, but luckily I have access to laser cutting and water-jet cutting for free. I have cut...
jolyboy's Avatar
Registered Users
Posted in Uncategorized
Views 1339 Comments 0 jolyboy is offline




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

SEO by vBSEO 3.6.1