START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Goblin 280 SAB Heli Division - Goblin 280 Helicopters |
|
LinkBack | Thread Tools | Display Modes |
01-15-2020, 08:26 AM | #1 (permalink) |
Registered Users
Join Date: Mar 2015
Location: Schweiz
|
Help with neo and Fireball
Hello,
I have bought a used Fireball last year(guy only assembled it, wrongly , it never flown) and I installed a vbar neo on it. Since last year I have been able to fly only 4-5 times. First because the original ESC died, like drop dead after the first flight and second, the new ESC is giving me issues. To start with, I am absolutely new with the Vbar Control and Neo(always had Spektrum for budget reasons) I have bought them because I fly 95% heli and it seemed a good choice for a TX and I have always heard good things about the VStabi first and the Neo later. Now, back to my problem. I have set up my Fireball following the manual. I have tried both neo and external governor in my setup. Each time I am on the field, I can do some flights and as soon as I swap the lipo, bom, the ESC doesn't beep when connected and I can't start the heli, I have to redo the ESC setup if I wanna fly again and this in the long run has become so annoying that I am leaving the Fireball home and bringing only the 380. This only happens with the Fireball, with the 380 that has a YGE ESC, never had a single issue. (Fireball also works perfectly if I use my old Spektrum or my bf's Graupner) Can someone please help me figure out what I am doing wrong with my Fireball/Vbar? Thank you very much!!
__________________
Goblin Fireball | Goblin 380 | T-Rex 600 ESP | Goblin Urukay | OMP M2 V2 | mCPX | Jeti DS-12 | neXt | |
Sponsored Links | |||
Advertisement |
|
01-15-2020, 09:59 AM | #2 (permalink) |
Registered Users
Join Date: Dec 2014
Location: always windy on the east coast
|
so what is the new esc your using? did you set it up in the esc menu in the vcontrol?
__________________
a bunch of helis... now all vcontrol and neo..finally :lol |
01-15-2020, 10:08 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2015
Location: Schweiz
|
I am using the stock one from Sab a hobbywing 60A.
Yes, I set it up as Unknown ESC.
__________________
Goblin Fireball | Goblin 380 | T-Rex 600 ESP | Goblin Urukay | OMP M2 V2 | mCPX | Jeti DS-12 | neXt | |
01-15-2020, 10:38 AM | #4 (permalink) |
Registered Users
Join Date: Dec 2014
Location: always windy on the east coast
|
end points set? vcontrol tx up to date?. plugged into vbar control manager and updated?
__________________
a bunch of helis... now all vcontrol and neo..finally :lol |
01-15-2020, 10:43 AM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2015
Location: Schweiz
|
Yes to all
__________________
Goblin Fireball | Goblin 380 | T-Rex 600 ESP | Goblin Urukay | OMP M2 V2 | mCPX | Jeti DS-12 | neXt | |
01-15-2020, 10:50 AM | #6 (permalink) |
Registered Users
Join Date: Dec 2014
Location: always windy on the east coast
|
what happens if you connect one lipo, fly, then unplug it but connect the same lipo? no ui sensor or telemetry, right?
__________________
a bunch of helis... now all vcontrol and neo..finally :lol |
01-15-2020, 04:00 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2015
Location: Schweiz
|
Depends, sometimes it flies and some other times it just stop working.
No, got no sensors. Batteries are good and tested.
__________________
Goblin Fireball | Goblin 380 | T-Rex 600 ESP | Goblin Urukay | OMP M2 V2 | mCPX | Jeti DS-12 | neXt | |
01-15-2020, 04:04 PM | #8 (permalink) |
Registered Users
Join Date: Dec 2014
Location: always windy on the east coast
|
Sounds like you got a bad connector somewhere
__________________
a bunch of helis... now all vcontrol and neo..finally :lol |
01-15-2020, 04:20 PM | #9 (permalink) |
Registered Users
Thread Starter
Join Date: Mar 2015
Location: Schweiz
|
But if it was that the same would happen when I use the Spektrum or the Graupner TX and it never happens, it only happens with the Mikado Vbar control.
In my opinion there is something I am not setting or I am setting wrongly and gets erased from time to time, just I have no idea of what it could be
__________________
Goblin Fireball | Goblin 380 | T-Rex 600 ESP | Goblin Urukay | OMP M2 V2 | mCPX | Jeti DS-12 | neXt | Last edited by the_jane_doe; 01-16-2020 at 03:49 AM.. |
Thread Tools | |
Display Modes | |
|
|