Align RCE-BL35G ESC startup problems - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Electric Micro/Mini Helicopters > X400 and MX400


X400 and MX400 Ark X400 and HeliMax MX400 Helicopters Information


Reply
 
LinkBack Thread Tools Display Modes
Old 01-24-2008, 11:32 AM   #1 (permalink)
Registered Users
 

Join Date: Jan 2008
Location: Live Oak, Florida
Default Align RCE-BL35G ESC startup problems

I have an the ...35G ESC installed in my MX400 and went through the setup with the Tx as per the instructions.

When I raise the throttle slowly, the motor jerks only a couple teeth on the main gear, making the blades turn a bit each time I try to start up. Finally, after about 3 or 4 trys, the soft start engages and the hs climbs up. Once it starts, it's working and flying great.

Any ideas on the sporadic inputs to the motor and then after a while it starts up?
Could it be the Low Throttle Response setting on 35G?

Thanks.


(using MX400, 35G esc, 3s/11.1/2100's, stock Helimax 2580kv motor, epa's 100% around, Futaba T6EX 2.4 Tx-Rx set, with esc settings: Brake Disabled, mid-timing, low batt-protection, Heli-1 mode, throttle response Low)
matt400 is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-25-2008, 01:33 AM   #2 (permalink)
Registered Users
 
Posts: 1,373
 
My HF Map location
Join Date: Mar 2006
Location: Portland, OR
Default

I had that happen. Check the connectors and make sure they are not loose. It might be timing or a break in the coils.
__________________
Team Outrage
OPM - Fly it like it aint yours!
JR X9303 2.4 Baby. I have felt the difference and I like it!
Don"t make me list 'm all !
Raven_darkcloud is offline        Reply With Quote Quick reply to this message
Old 09-08-2009, 09:01 AM   #3 (permalink)
Registered Users
 

Join Date: Jul 2009
Location: Windsor, Ct
Default

Matt i having some what the same problem. I have a t-rex 450xl. when i start up my heli, it run for 30sec and then starts to buck, then it shut down then start up again by itself. it keep doing that at 1/4 thro position. It get hot quick. when i could pick it off the ground time i pick it up to hover it comes back down. now it start bucking again. Anybody knows what could be the problem? The connectors are fine. How do you check the timing? Thank you.
Madden is offline        Reply With Quote Quick reply to this message
Old 09-08-2009, 10:20 AM   #4 (permalink)
Registered Users
 

Join Date: Dec 2008
Location: Beijing
Default

Dear Matt I had also that problems take care if it gets too hot the bec in the ESC wont work anymore. Then you have failsafe on your helicopter which is not really nice. My dealer exchanged the ESC for free. But anyway I installed a sperate BEC which is the little money really worth. One safed crash is enough.

Jan
Jannie is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © VerticalScope Inc. All rights reserved.
 

SEO by vBSEO 3.6.1