V200D03 motor is still not running. - Page 2 - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Walkera Helicopters > Others


Others Walkera Other Models Helicopter Support


Reply
 
LinkBack Thread Tools Display Modes
Old 04-14-2012, 09:49 PM   #21 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Feb 2012
Location: USA
Default

Yes the wires are connected correctly. The battery voltage is good. But I will follow up on other ideas and let the group know the outcome.
Thank you all for your suggestions.
Aftab.
Aftab is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 04-15-2012, 04:36 AM   #22 (permalink)
Registered Users
 

Join Date: Dec 2011
Location: Jacksonville, FL
Default

What about checking output from esc?
__________________
Walkera v200d03, v120d02s on Devo 8s
Realflight 6.5
HRPuffnstuff is offline        Reply With Quote Quick reply to this message
Old 04-15-2012, 10:06 AM   #23 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Feb 2012
Location: USA
Default

How do you check output from ESC?
Thanks,
Aftab.
Aftab is offline        Reply With Quote Quick reply to this message
Old 04-15-2012, 03:34 PM   #24 (permalink)
Registered Users
 

Join Date: Feb 2012
Location: London
Default

I think you'd need a voltage meter.
Benvk is offline        Reply With Quote Quick reply to this message
Old 04-15-2012, 04:27 PM   #25 (permalink)
Registered Users
 

Join Date: Dec 2011
Location: Jacksonville, FL
Default

I was thinking disconnect the motor and attach probles to ground and positive output from esc and measure the output but since bl's are 3 wire it might not be that simple. You should at least see some output from the esc and it should change as you increase/decrease the throttle.
__________________
Walkera v200d03, v120d02s on Devo 8s
Realflight 6.5
HRPuffnstuff is offline        Reply With Quote Quick reply to this message
Old 04-15-2012, 06:53 PM   #26 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Feb 2012
Location: USA
Default

I will see if I can borrow voltage meter from someone and also learn how to use and interpret the readings. I think it might not be that complicated but still good to get advice.
Thanks,
Aftab.
Aftab is offline        Reply With Quote Quick reply to this message
Old 04-16-2012, 05:33 PM   #27 (permalink)
Registered Users
 

Join Date: Dec 2011
Location: Jacksonville, FL
Default

I almost bought another motor today as I was thinking about this thread. The stock with its pressed on pinion doesn't inspire long term confidence with me. Any luck with getting readings from the esc?
__________________
Walkera v200d03, v120d02s on Devo 8s
Realflight 6.5
HRPuffnstuff is offline        Reply With Quote Quick reply to this message
Old 04-22-2012, 12:31 PM   #28 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Feb 2012
Location: USA
Default

Stupid me. After spending money on new ESC and new motor it turned out that I was putting the connector from the ESC in the wrong slot of receiver. Interestingly when you put it in the slot that says 5V all the rest of the servos work it is just the motor that does not get power.
How stupid of me. Thanks guys anyway. I did learn stuff though, through this thread.
Aftab.
Aftab is offline        Reply With Quote Quick reply to this message
Old 04-22-2012, 02:56 PM   #29 (permalink)
Registered Users
 

Join Date: May 2010
Location: los angeles, ca
Default

Quote:
Originally Posted by Aftab View Post
Stupid me. After spending money on new ESC and new motor it turned out that I was putting the connector from the ESC in the wrong slot of receiver. Interestingly when you put it in the slot that says 5V all the rest of the servos work it is just the motor that does not get power.
How stupid of me. Thanks guys anyway. I did learn stuff though, through this thread.
Aftab.
Good you got it together. Sometimes its the simple thing we overlook hahaha. Yup it goes in throttle plug my manual sits right next to the computer. Next time check Manual it show how everything goes. Hay miracle-mart has stock blades in stock for $14. Mine has a little left drift on take off but no big deal I'm used to it now don't want to mess with a great flying heli. Have fun Vronny
vronny is offline        Reply With Quote Quick reply to this message
Old 04-22-2012, 04:14 PM   #30 (permalink)
Registered Users
 

Join Date: Feb 2012
Location: London
Default

Look on the bright side, you now have a spare motor and esc!
Benvk is offline        Reply With Quote Quick reply to this message
Old 04-22-2012, 04:47 PM   #31 (permalink)
Registered Users
 
Posts: 207
 

Join Date: Apr 2012
Location: Ohio
Default

Quote:
Originally Posted by Benvk View Post
Look on the bright side, you now have a spare motor and esc!
LOL
bvento is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
 

SEO by vBSEO 3.6.1