Spectrum ar6115 won't move my Align TREX 250 servos! - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > 250 Class Electric Helicopters


250 Class Electric Helicopters 250 Class Electric Helicopters manufactured by Align, Tarot, SYMA, Airhog, Chaos, HK and similar.


Reply
 
LinkBack Thread Tools Display Modes
Old 05-08-2012, 12:22 AM   #1 (permalink)
Registered Users
 

Join Date: May 2012
Location: Calgary, Alberta
Default Spectrum ar6115 won't move my Align TREX 250 servos!

I was setting up my Align TREX 250 servos and they were working fine, but then I set my pitch curves to level the swash and accidently reconnected to the Spectrum ar6115 with the throttle at 50% (on my DX6i)and the servos just "chatter" and the receiver just blinks the red "hold" led.......I've tried to rebind but the receiver just won't "talk" to the servos any more, I even replaced the receiver but the same thing happens. I don't think that I changed any other settings on the DX6i so I don't know what else check/replace.
Hitchb is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 05-08-2012, 03:20 PM   #2 (permalink)
Registered Users
 
Posts: 463
 
My HF Map location
Join Date: Aug 2010
Location: Nelson NZ
Default

Have u tried just esc, rx and binding it?
__________________
Yes I miss the odd screw, so what

Trex 700N Vbar, Mikado LOGO 600SX, Trex 450 SportV2, Trex 250se-dfc, MCPX ...DX8...
kiwianaBrad is offline        Reply With Quote Quick reply to this message
Old 05-08-2012, 04:44 PM   #3 (permalink)
Registered Users
 
Posts: 1,877
 
My HF Map location
Join Date: Apr 2011
Location: Oakville, ON - CDN
Default

Rebind to a clean model, or put your pitch curve back to a linear 0 -> 100

It's probably your curve or swash mix that you said you changed to level the swash. If you haven't finished your swash mix then you won't get any movement on aile or elev.

I always bind at mid-stick with TH on so if the signal drops and goes to failsafe, it's set at 0 pitch (not -12 ) and a recoverable throttle value (about 15%).
__________________
TRex 250 DFC | TRex 250 DFC (Scale)
2 @ TRex 450 DFC | TRex 450 Pro 3G (Scale)
TRex 550 DFC
DX8 + Telemetery on all
JoeW is offline        Reply With Quote Quick reply to this message
Old 05-12-2012, 07:12 PM   #4 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: May 2012
Location: Calgary, Alberta
Default servo problem solved

I took a guess that it might be the ESC due to the fact that there didn't seem to be any power getting to the servos, got a replacement yesterday and everything seems to be working fine, thanks for the replies.
Hitchb is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
 

SEO by vBSEO 3.6.1