Doublehorse 9116 4 ch - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Other Makes and Models Helicopters


Other Makes and Models Helicopters Other makes and model Helicopters


Reply
 
LinkBack Thread Tools Display Modes
Old 01-29-2012, 11:25 AM   #1 (permalink)
Registered Users
 

Join Date: Jan 2012
Location: USA-IL
Default Doublehorse 9116 4 ch

I have a new DH 9116 4 ch and had a hard landing (crashed into bookcase inside house)

Since then, the tail rotor goes into almost full spin up at hit of throttle causing loss of control at rudder function. Normally, the tail rotor doesn't even spin up at all in low throttle unless right rudder is thrown in causing tail rotor to spin up. Now, it is in full action at neutral rudder and slows only slightly at left rudder and full (normal) spin at full right rudder.

Suggestions? Bad servo? Knocked way out of whack from crash? I always turn radio on first and then heli waiting for tx/rx to properly align w/each other.

HELP!
Bildnfly is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 02-10-2012, 12:08 AM   #2 (permalink)
Registered Users
 

Join Date: Feb 2012
Location: Kansas
Default Double Horse 9116

I also have a Double Horse 9116 that I have been working with outside during the warmer weather. Quite a docile heli.

Sounds as though you may have damaged the motherboard or the tail motor itself.

When getting into trouble with them it is best to set them down & shut off the throttle.

You might also check out the following RC Groups Discussion - - there are about 100 pages plus about the Double Horse 9116:

http://www.rcgroups.com/forums/showt...358424&page=98

Hope this my help you.

Jim
KsWhirly is offline        Reply With Quote Quick reply to this message
Old 02-10-2012, 12:27 AM   #3 (permalink)
Registered Users
 

Join Date: Feb 2012
Location: Kansas
Default Double Horse 9116

I apologize, I pulled the wrong location for the 9116. Here is the thread covering the 9116 - - there is a lot of activity on both the 9100 and the 9116:

http://www.rcgroups.com/forums/showt...540154&page=63

Jim
KsWhirly is offline        Reply With Quote Quick reply to this message
Old 06-06-2012, 04:39 PM   #4 (permalink)
Registered Users
 
Posts: 179
 
My HF Map location
Join Date: May 2012
Location: Windsor Ontario Canada
Default

I just did a feasibility study on if its possible to make a spare 9116 canopy from a pop bottle ,...It appears to be possible ,.....but it can be done alot better than what I came up with,....




Last edited by dogtoy; 06-06-2012 at 05:41 PM..
dogtoy is offline        Reply With Quote Quick reply to this message
Old 11-20-2012, 12:11 PM   #5 (permalink)
Registered Users
 
Posts: 250
 

Join Date: Aug 2012
Location: hurricane Utah
Default

So I have this idea.

I love my DH 9116 even though I am flying CP helies, I still fall back on the 9116 for a quickie in the front yard.. its a lot of fun.

Heres my idea. I have enough parts to build a second heli.. BUT what about maiking it more maneuverable/agile by making it a little more programmable. I want to throw in my spektrum receiver to run the thing.

I have a e-flight ESC 2 in 1 from my SR. so I am figuring I can run that, and have it power my tail and main motors. my question is.. how would i set up the DX6I to control the elevator/aileron channels?? if I set it to CCPM wont it be setting it up for 3 servos? not two??

Should I maybe look up the setting for say a blade 120 sr and use those??

any input would be greatly appreciated..

heck if this works out i think it will ROCK. just gotta find the right settings and a brushless motor to fit it.. maybe the 130x motor?? and an n6 for the tail??
metalwizard is offline        Reply With Quote Quick reply to this message
Old 01-23-2013, 01:51 PM   #6 (permalink)
Registered Users
 

Join Date: Jan 2013
Location: Midwest
Default

Did you ever find a solution to the tail rotor spin up?
RobG1 is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © VerticalScope Inc. All rights reserved.
 

SEO by vBSEO 3.6.1