START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
DJI Multirotor Forum(A2/WKM) DJI Multirotor Forum(A2/WKM) |
|
LinkBack | Thread Tools | Display Modes |
12-31-2013, 03:04 AM | #41 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released assistant software for Mac!
Mac style interface
Clean, modern Mac inspired interface that Mac users will love. Different system, same operation Usage is the same on Mac and PC versions, so if you’re used to the PC version you can switch straight over. No more driver installs No more downloading drivers to install Assistant. It just works. https://www.youtube.com/watch?v=9nmM9qFljPk Operating system: Mac OS X 10.6(Lion) or above Supported flight systems: Phantom 2 Vision, Phantom 2, A2 Please click here to download the Mac Assistant Software for Phantom 2 Vision. Please click here to download the Mac Assistant Software for Phantom 2. Please click here to download the Mac Assistant Software for A2. |
Sponsored Links | |||
Advertisement |
|
12-31-2013, 08:07 AM | #42 (permalink) |
Registered Users
|
will there be the other components for MacOSX as well, like the RC Assistant, iOSD etc?
|
12-31-2013, 08:35 AM | #43 (permalink) | |
HF MR Support
Join Date: Mar 2012
|
Quote:
I think the MAC UI is great move Would love to see a I-phone Assistant App as well...
__________________
~ HeliFreak MR Support |
|
12-31-2013, 10:55 AM | #44 (permalink) |
Registered Users
|
well its quite pointless if you cant upgrade all components due to other apps not being available ... hence my question but if they dont reply I wont be checking back for an answer then ...
|
01-09-2014, 07:42 AM | #45 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released new firmware for Phantom 2 remote control!
What’s new?
Firmware Remote Controller firmware updated to V1.0.1.11 Optimized output of the X1 channel on the Phantom 2 remote controller to improve user experience. Important notes: 1.For the users of the PHANTOM 2 with Zenmuse H3-2D gimbal, one must adhere to the following steps to upgrade the remote controller firmware. 1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11. 2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software. 3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via upgrade page. 4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D. 2.For users of PHANTOM 2 without Zenmuse H3-2D, conduct all of the above steps except the third to upgrade the remote controller firmware. Please click here for more information. |
01-09-2014, 07:44 AM | #46 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released new firmware for Phantom 2 remote control!
What’s new?
Firmware Remote Controller firmware updated to V1.0.1.11 Optimized output of the X1 channel on the Phantom 2 remote controller to improve user experience. Important notes: 1.For the users of the PHANTOM 2 with Zenmuse H3-2D gimbal, one must adhere to the following steps to upgrade the remote controller firmware. 1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11. 2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software. 3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via upgrade page. 4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D. 2.For users of PHANTOM 2 without Zenmuse H3-2D, conduct all of the above steps except the third to upgrade the remote controller firmware. Please click here for more information. |
01-09-2014, 09:27 AM | #47 (permalink) |
Registered User
Join Date: Jul 2012
|
The last 2 posts by who ever is posting for DJI, just proves what we've been saying this entire thread. "sigh"
|
01-09-2014, 09:41 AM | #48 (permalink) |
Registered User
|
Empire RC is doing the support in this country from my understanding. There is definitely a language barrier issue involved here.
__________________
William James Crazy wife still trying to kill me. |
01-09-2014, 05:52 PM | #49 (permalink) |
Registered User
Join Date: Jul 2012
|
Unless you have a Chinese language pack in this forum, they have to know enough English to navigate around the forum to know where to post the ads. And they post at another forum that shall remain nameless. You know the one with the incredibly long threads. If they can navigate around that mess then they know enough English to stop and try to respond to us.
|
01-12-2014, 09:53 PM | #50 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI is going to release an FPV Hub Kit for Phantom 2!
PHANTOM 2 FPV HUB kit contains only cables and the FPV HUB to make connections convenient, easy and thus removing the need to do soldering when connecting them to a iOSD mini,iOSD Mark II or a DJI specified wireless video transmission module AVL58. Only 4 cables require soldering if users opt to use a wireless video transmission that’s not specified by DJI.
Connections Choose devices collocation used with FPV-HUB according to required functions. For wireless video transmission, the ALV58 is recommended for easy connection, using a HUB-AVL58 cable. Collocation 1: Wireless video transmission module connected 1)Stop the Micro switch at VID position if only wireless video transmission module is connected to the FPV HUB. 2)Wireless video transmission module is an alternative to AVL58 or others unspecified. If using the AVL58, connect it to the FPV HUB via HUB-AVL58 cable. If using other wireless video transmission module, connect it to the FPV HUB via HUB-VTX cable according to pins description of the HUB-VTX cable. Collocation 2&3: iOSD mini/iOSD MARK II and video transmission module connected 1)It’s alternative to use iOSD mini or iOSD Mark II. 2)Stop the Micro switch at OSD position when iOSD is connected to the FPV HUB. 3)Please refer to Collocation1 to connect the wireless video transmission module. Notes: (1)If using the FPV HUB, the original 4-Pin cable and video cable on PHANTOM 2 will be spared, please remove and clear them out. Make sure the video cable is totally cleared without any copper wire left to prevent short circuit damage. (2)All connection operations should be conducted when the intelligent battery is powered off. (3)Check whether pins of the connectors on the FPV HUB are straight and in good condition before connecting. Pls plug and unplug the connector carefully to avoid damage or short circuit. (4)It’s not recommended to install the FPV HUB and extended devices inside the PHANTOM 2 aircraft. (5)Make sure to install the AVL58 away from the compass to avoid interference. (6)FPV HUB is non water-proof, if it is wet, please wash it with alcoholic cleanser and dry it before use. Otherwise components may be damaged cause of electrochemical corrosion. (7)Do not leak any metal, conductive objects into the connector pins of FPV HUB to prevent short circuit damage. (8)It’s not recommended to use cables not in the kit to connect devices to avoid unexpected damage. (9)Make sure the connection is correct when using non-DJI recommended wireless video transmission module. Tips: (1)FPV HUB has a resettable fuse for over circuit precaution. The fuse will automatically open if the working current of power consuming devices (except DJI Zenmuse series) goes over 2A or if VCC and GND short circuited to prevent damage. After the short circuit trouble issued or the over current load is removed, turn off the power of the intelligent battery, the fuse will recover after 10secs. (2)A component will be damaged if PHANTOM 2 has been short circuit once. In this condition, users still can use the FPV HUB and make the PHANTOM 2 work well again, ignoring the damaged component. Last edited by DJI Innovations; 01-12-2014 at 11:39 PM.. |
01-12-2014, 09:55 PM | #51 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI is going to release an FPV Hub Kit for Phantom 2!
PHANTOM 2 FPV HUB kit contains only cables and the FPV HUB to make connections convenient, easy and thus removing the need to do soldering when connecting them to a iOSD mini,iOSD Mark II or a DJI specified wireless video transmission module AVL58. Only 4 cables require soldering if users opt to use a wireless video transmission that’s not specified by DJI.
Connections Choose devices collocation used with FPV-HUB according to required functions. For wireless video transmission, the ALV58 is recommended for easy connection, using a HUB-AVL58 cable. Collocation 1: Wireless video transmission module connected 1)Stop the Micro switch at VID position if only wireless video transmission module is connected to the FPV HUB. 2)Wireless video transmission module is an alternative to AVL58 or others unspecified. If using the AVL58, connect it to the FPV HUB via HUB-AVL58 cable. If using other wireless video transmission module, connect it to the FPV HUB via HUB-VTX cable according to pins description of the HUB-VTX cable. Collocation 2&3: iOSD mini/iOSD MARK II and video transmission module connected 1)It’s alternative to use iOSD mini or iOSD Mark II. 2)Stop the Micro switch at OSD position when iOSD is connected to the FPV HUB. 3)Please refer to Collocation1 to connect the wireless video transmission module. Notes: (1)If using the FPV HUB, the original 4-Pin cable and video cable on PHANTOM 2 will be spared, please remove and clear them out. Make sure the video cable is totally cleared without any copper wire left to prevent short circuit damage. (2)All connection operations should be conducted when the intelligent battery is powered off. (3)Check whether pins of the connectors on the FPV HUB are straight and in good condition before connecting. Pls plug and unplug the connector carefully to avoid damage or short circuit. (4)It’s not recommended to install the FPV HUB and extended devices inside the PHANTOM 2 aircraft. (5)Make sure to install the AVL58 away from the compass to avoid interference. (6)FPV HUB is non water-proof, if it is wet, please wash it with alcoholic cleanser and dry it before use. Otherwise components may be damaged cause of electrochemical corrosion. (7)Do not leak any metal, conductive objects into the connector pins of FPV HUB to prevent short circuit damage. (8)It’s not recommended to use cables not in the kit to connect devices to avoid unexpected damage. (9)Make sure the connection is correct when using non-DJI recommended wireless video transmission module. Tips: (1)FPV HUB has a resettable fuse for over circuit precaution. The fuse will automatically open if the working current of power consuming devices (except DJI Zenmuse series) goes over 2A or if VCC and GND short circuited to prevent damage. After the short circuit trouble issued or the over current load is removed, turn off the power of the intelligent battery, the fuse will recover after 10secs. (2)A component will be damaged if PHANTOM 2 has been short circuit once. In this condition, users still can use the FPV HUB and make the PHANTOM 2 work well again, ignoring the damaged component. Last edited by DJI Innovations; 01-12-2014 at 11:40 PM.. |
01-12-2014, 10:40 PM | #52 (permalink) | |
HF MR Support
Join Date: Nov 2012
|
Quote:
I do like the little FPV interconnect board though.
__________________
3 years cancer free! Woot!! ~ Cancer can kiss my grits! Ainokea! If you never crash, you're not having enough fun! Pilot, Team Lavaquad |
|
01-12-2014, 10:57 PM | #53 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released new firmware for Zenmuse H3-2D!
What’s new?
Firmware Optimized user experience when using the PHANTOM 2 remote controller for Zenmuse H3-2D pitch control. Important notes for PHANTOM 2 users: For users of the PHANTOM 2 with Zenmuse H3-2D, one must adhere to following steps to upgrade the remote controller firmware. 1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11. 2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software. 3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via Upgrade page. 4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D. Please click here for more information. |
01-12-2014, 10:58 PM | #54 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released new firmware for Zenmuse H3-2D!
What’s new?
Firmware Optimized user experience when using the PHANTOM 2 remote controller for Zenmuse H3-2D pitch control. Important notes for PHANTOM 2 users: For users of the PHANTOM 2 with Zenmuse H3-2D, one must adhere to following steps to upgrade the remote controller firmware. 1)Use the PHANTOM RC Assistant software to upgrade the remote controller firmware to V1.0.1.11. 2)Calibrate the sticks and X1 channel of the remote controller using the PHANTOM RC Assistant software. 3)Use the PHANTOM 2 Assistant software to upgrade the Gimbal IMU firmware to V1.8 via Upgrade page. 4)After the upgrade is completed, calibrate the X1 channel of the main controller using the PHANTOM 2 Assistant software to ensure compatibility of PHANTOM 2 and the Zenmuse H3-2D. Please click here for more information. |
01-12-2014, 11:31 PM | #55 (permalink) |
Registered Users
Join Date: Sep 2013
|
bla bla bla everytime a company sells their product like hell people bashes.
same thing with align, now the attacks are for DJI
__________________
Don't do like me. Do not live in a s*hole |
01-12-2014, 11:58 PM | #56 (permalink) |
Registered User
Join Date: Jul 2012
|
It's not attacks, it's facts. Internally DJI has the worst tech support. It's dealers like Empire that do what they can to support us. And what they can't do we rely on other end users for help.
It's not bashing or attacking, it's statements of fact. If they stepped up to the plate publicly, I would venture that a large portion of the problems that occur with DJI products would be resolved and rather quickly. They even told us they were in the process of opening a service center on US soil and that's the last we heard of that. Couple of months ago, I think it was. Simply put it's a manufacturer of a product choosing to ignore or make its customers jump through flaming hoops to get help with their product. The way they treat us is uncalled for. |
01-13-2014, 12:50 AM | #57 (permalink) |
HF MR Support
Join Date: Nov 2012
|
You really should read the entire thread... and then show us even a single example of anybody here bashing their products. You must have seen something that prompted you to accuse us of bashing their stuff. We'd like to see it.
__________________
3 years cancer free! Woot!! ~ Cancer can kiss my grits! Ainokea! If you never crash, you're not having enough fun! Pilot, Team Lavaquad |
01-24-2014, 06:12 AM | #58 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released the FPV HUB, camera mounting bracket and prop guard for Phantom 2!
PHANTOM 2 FPV HUB
In the kit: FPV HUB, cables and instructions Function: Customized ports and cables for iOSD mini, iOSD Mark II or AVL58. Feature: FPV HUB’s integrated iOSD mini,iOSD Mark II or AVL58 ports, connecting directly to the PHANTOM 2 central board and built-in main controller through an 8-Pin cable. This simplifies connecting these items and eliminates the need for soldering. PHANTOM 2 Camera Mounting Bracket In the kit: Camera mounting bracket and screws Function: Attachment for GoPro cameras and others. Feature: Gimbal free camera attachment for GoPro and similar cameras. PHANTOM 2 Prop Guard In the kit: 4 prop guards and instructions Function: Fitted under the rotors to prevent damage to rotors or surroundings. Feature: Easy to attach, lightweight, safe and reliable. Specifications: Weight (Single): 21g Angle: 150.0° Radius: 128.25mm Whole Size with Four Prop Guards: 613mm Important Notes: Make sure the PHANTOM 2 weighs no more than 1350g after mounting prop guards. Any extra weight will compromise flight capabilities causing a safety risk. The total weight of a PHANTOM 2 with H3-2D gimbal, iOSD and wireless video transmitter will be over 1300g, prop guards are not recommended for similarly equipped PHANTOM 2s. Please click here for more information. |
01-24-2014, 06:13 AM | #59 (permalink) |
Registered Users
Thread Starter
Join Date: Aug 2010
|
DJI released the FPV HUB, camera mounting bracket and prop guard for Phantom 2!
PHANTOM 2 FPV HUB
In the kit: FPV HUB, cables and instructions Function: Customized ports and cables for iOSD mini, iOSD Mark II or AVL58. Feature: FPV HUB’s integrated iOSD mini,iOSD Mark II or AVL58 ports, connecting directly to the PHANTOM 2 central board and built-in main controller through an 8-Pin cable. This simplifies connecting these items and eliminates the need for soldering. PHANTOM 2 Camera Mounting Bracket In the kit: Camera mounting bracket and screws Function: Attachment for GoPro cameras and others. Feature: Gimbal free camera attachment for GoPro and similar cameras. PHANTOM 2 Prop Guard In the kit: 4 prop guards and instructions Function: Fitted under the rotors to prevent damage to rotors or surroundings. Feature: Easy to attach, lightweight, safe and reliable. Specifications: Weight (Single): 21g Angle: 150.0° Radius: 128.25mm Whole Size with Four Prop Guards: 613mm Important Notes: Make sure the PHANTOM 2 weighs no more than 1350g after mounting prop guards. Any extra weight will compromise flight capabilities causing a safety risk. The total weight of a PHANTOM 2 with H3-2D gimbal, iOSD and wireless video transmitter will be over 1300g, prop guards are not recommended for similarly equipped PHANTOM 2s. Please click here for more information. |
01-24-2014, 11:46 AM | #60 (permalink) |
HF MR Support
Join Date: Mar 2012
|
I thought we weren't to advertise in the main discussion forums
" Discussion forums are created for the exchange of support information and are to remain free of commercial/retail activity. Announcements, build threads, reviews, and other related threads, are to be posted to the Manufacturers, Dealers, Resellers, Announcements forum."
__________________
~ HeliFreak MR Support |
Thread Tools | |
Display Modes | |
|
|