Xnova motor delayed

[xnovamotors-support]

Originally Posted by Luigi_tuga

This issue happens specially with high KV, around 1800 kv.
On 1300 kv there are less issues, even less around 900.
Less KV demand less processing/switching speed from the ESC

Hello.

Exactually corect answer.

1.
YGE ESC was working very well also.
YGE: 18 for timing or higer ,PWM Start with 8 (also auto-timing works good on YGE with Xnovamotors)

thank you.
xnovamotors_support

[ken234]

I had nothing but good things to say about the motor or quality of it,the problem is these things should be tested before sending to the consumer,in my opinion anyway,had I known there would be issues I probably wouldn't have bought it.I was actually going to put the tareq motor in my 380,but was hesitant because I could never get the 1860 to work.

[BLAZE86DUBZ]

now im hesitant about this Xnova 2820-890KV moter this is the one i purchased i never had a yge 90 lv esc i have never used one before i bought the program card but i never had to play with timing before on a esc

[snemi00]

Originally Posted by BLAZE86DUBZ

now im hesitant about this Xnova 2820-890KV moter this is the one i purchased i never had a yge 90 lv esc i have never used one before i bought the program card but i never had to play with timing before on a esc

No reason to be hesitant, that will be an awesome combo believe me.
The YGE defaults for timing and PWM are 18° and either 8 or 10 PWM, perfect.

[sturebergdahl]

Originally Posted by BLAZE86DUBZ

now im hesitant about this Xnova 2820-890KV moter this is the one i purchased i never had a yge 90 lv esc i have never used one before i bought the program card but i never had to play with timing before on a esc

what governor you plan to use?

[BLAZE86DUBZ]

im not sure yet i have the spartin vortex fbl unit was going to try that

[sturebergdahl]

Mayby this programing video will help you. http://vstabi.info/en/node/1476

[BLAZE86DUBZ]

It's not a vbar

[ragge1]

are you thinking of trying the vortex gov with the YGE , see this

Spartan Vortex - eGov basic setup (in HD) w/ guide for YGE low voltage ESC (18 min 30 sec)

[BLAZE86DUBZ]

i wasent worried about the gov setup i was worried about the timing i never had to use a esc and moter combo and i had to set the timing

[ragge1]

timming on outrunner motor for YGE = 18
PWM 8-12 I think , gonna have mine at 10 and check the esc temp after flight

[BLAZE86DUBZ]

so they dont have auto timing on yge?? u have to set it urself?

[ken234]

You need to use the program card,I think auto timing is on the first page at the very bottom all the way to the right

[BLAZE86DUBZ]

well whats better ?? auto or reg timing for Xnova 2820-890KV 10P ?

[Inverted2112]

There is no auto for timing, only for startup power.

Try 18degrees for timing. Typical for all outrunners as previously mentioned.

[para5063]

Originally Posted by Inverted2112

There is no auto for timing, only for startup power.

Actually on the program card for the YGE, there's a special section and AUTO Timing is there. When enabled, the static timing selection is cleared.

[ken234]

Yes and actually if you go on xnova website they recommend auto timing

[ken234]

orXnova XTS motors are not picky about ESC settings. Most default settings are just fine, but there are some things to consider. Please find setup examples below

Castle Creation ESC :

16Khz and 8 for timing.

Kontronik ESC :

Reset ESC by Mode 1, then use Autotiming Mode 4.

KOSMIK expert-setup sample for XTS-4530-480KV Motor: Mode 1 , then Mode 4. Go to advanced settings and select RI compensation= 12 ( this is the RM number of the XTS-4530-480kv motor which can be found for all our motors under technically details). P gain increase from 4 to 5.

(this is a advanced setup sample. the basic setup Mode 1 then Mode 4 will satisfied most pilots)

YGE ESC:

Autotiming and start with 8 PWM.

Scorpion ESC :

Current protection=normal/ (commander 160) insensitive/ (commander 130) /Motor-timing 5* . Gov. tuning 6-for P-gain and 7-for I-gain.

Hobbywing ESC :

Setup example: Platinum-50A-V3 with XTS 2618 series.

- Timing 8°
- PWM: 8Khz or 16Khz (Batteries are less warm with 8khz)

Heli specific setup:

[Inverted2112]

My bad, its under special functions....

Can't say how many times I've used the darned thing and I had never noticed that....

Originally Posted by para5063

Actually on the program card for the YGE, there's a special section and AUTO Timing is there. When enabled, the static timing selection is cleared.

[vertico]

@ Helidirect, Delayed again! ETA now 1/21!