Register Now

OddJack · 07-04-2016, 09:54 AM

Anyone here uses the radio for FBL heli?

OddJack · 07-04-2016, 10:22 AM

I guess not possible, just read on the other thread

TMoore · 07-15-2016, 12:46 PM

I do.

Helibelly · 07-16-2016, 04:59 PM

Hi, should be no problem if the flybarless unit supports standard receivers.
I am using its "little brother", if you will, the RDS8000, with the Spirit flybarless unit. No probs, Eric.

Dennis P · 07-18-2016, 10:41 AM

I do not personally anymore but still use it on my planes. I have a few fellow flyers that are flying helis with them and they are a great radio . The only down fall is more wiring and you may loose some options on bank switching ect when using a conventional receiver setup.

3Dmuse · 07-19-2016, 03:55 AM

I've been wondering about this recently myself and I'm not sure if it works. Futaba makes a PWM to SBus converter. Wouldn't it be possible to use this to essentially make any traditional receiver into a 1-wire output receiver?

Patriot996 · 07-19-2016, 07:04 PM

I saw that converter and wondered the same thing myself. I'd love to get an answer to this one.

JasonA · 09-04-2016, 11:23 AM

I only fly SD-10g and have a tons of helis and all vBAR. of course it works and it's awesome!

There's a few high end models they make that are PWM output and I run one of them with my naza. But for the rest, I run all independent ch's to the inputs..

Probably still the fastest out there in FHSS-3 mode too.

07-04-2016, 09:54 AM	#1 (permalink)
OddJack Registered Users Join Date: Jun 2016	SD 10G with Flybarless Helicopters Anyone here uses the radio for FBL heli? __________________ Goblin 700

07-04-2016, 10:22 AM	#2 (permalink)
OddJack Registered Users Thread Starter Join Date: Jun 2016	I guess not possible, just read on the other thread __________________ Goblin 700

07-18-2016, 10:41 AM	#5 (permalink)
Dennis P Registered Users My HF Map location Join Date: Aug 2010 Location: Rycroft , Alberta, Canada	I do not personally anymore but still use it on my planes. I have a few fellow flyers that are flying helis with them and they are a great radio . The only down fall is more wiring and you may loose some options on bank switching ect when using a conventional receiver setup. __________________ Rycroft Wings & Blades (MAAC Club) Rotor-Tech Blades

09-04-2016, 11:23 AM	#8 (permalink)
JasonA Registered Users Join Date: Jul 2011	I only fly SD-10g and have a tons of helis and all vBAR. of course it works and it's awesome! There's a few high end models they make that are PWM output and I run one of them with my naza. But for the rest, I run all independent ch's to the inputs.. Probably still the fastest out there in FHSS-3 mode too. __________________ Grauper MZ-24, Slope Racer/Soarer/Dynamic Soarer Guru Too many planes to list...Too many helis pro.. Tesla 100d, X-Raven/LongRange (Wife's), and 2014 Tesla pwrd Rav4ev

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-15-2016, 12:46 PM	#3 (permalink)
TMoore Registered Users Join Date: Apr 2004	I do.

07-16-2016, 04:59 PM	#4 (permalink)
Helibelly Registered Users Join Date: May 2006	Hi, should be no problem if the flybarless unit supports standard receivers. I am using its "little brother", if you will, the RDS8000, with the Spirit flybarless unit. No probs, Eric.

07-19-2016, 03:55 AM	#6 (permalink)
3Dmuse Registered Users Join Date: Apr 2009	I've been wondering about this recently myself and I'm not sure if it works. Futaba makes a PWM to SBus converter. Wouldn't it be possible to use this to essentially make any traditional receiver into a 1-wire output receiver?

07-19-2016, 07:04 PM	#7 (permalink)
Patriot996 Registered Users My HF Map location Join Date: Dec 2007	I saw that converter and wondered the same thing myself. I'd love to get an answer to this one.

Register Now

Log-in