Please help with vstabi 5.3 mini vbar setup - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Electronics Support > Mikado V-BAR


Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support


Like Tree1Likes
  • 1 Post By K2Freak
Reply
 
LinkBack Thread Tools Display Modes
Old 10-24-2017, 02:08 AM   #1 (permalink)
Registered Users
 

Join Date: Aug 2009
Location: Eureka, Ca
Default Please help with vstabi 5.3 mini vbar setup

Hi, can anyone please advise me on what is going on.

I connect to vstabi 5.3.

All green lights

When it gets to transmitter adjustments on the third tab, my collective is displaying fine, but the throttle / esc stays at 0% and does not seem to be "synced" to the collective.

My tx shows that the collective and throttle are moving together, but it seems on vstabi that they do not.

Any thoughts or advide would be greatly appreciated.

esc is an Exceed RC proton 40A OPTO. I am running power for the setup through a 2s rx pack.
EXI450DUDE is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-24-2017, 02:14 AM   #2 (permalink)
Registered Users
 
My HF Map location
Join Date: Oct 2011
Location: The Netherlands
Default

What radio and reciever?
__________________
Gaui X3 HW 50A V3 OMG H1/H2 Servo's BL450MX Mini-V (M.I.A.)
Gaui X5 FES Polaris BEC BLS451/251 Silverline V-Bar Formula Swash/Head
JR Forza 700 Scorp 160A opto + 4525 520 JR NX8925/SLG01 Vbar Neo
JR XG14 PL8 v2
mverhorst is offline        Reply With Quote Quick reply to this message
Old 10-24-2017, 04:31 AM   #3 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Eureka, Ca
Default

I am using the flysky th9x tx and the flysky fs-r8b rx
EXI450DUDE is offline        Reply With Quote Quick reply to this message
Old 10-24-2017, 06:38 AM   #4 (permalink)
Registered Users
 
Posts: 2,374
 

Join Date: Mar 2011
Location: Gillette, WY, USA
Default

On the receiver tab where you select your receiver type it shows the channel with boxes next them with numbers. You can click the numbers and change them. Since your not using a radio that is in the list the channel mapping may be off a little.


Sent from my iPhone using Tapatalk
tshelby73 is offline        Reply With Quote Quick reply to this message
Old 10-24-2017, 02:46 PM   #5 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Aug 2009
Location: Eureka, Ca
Default

Hello shelby, thank you for the reply.

I am unable to "change the numbers" in the rx tab. Maybe I have a different version than you. I have vstabi 5.3.4

I am pretty sure that it qualifies as a "standard receiver" though.

Some folks said that I have to plug the esc into the mini kabr, but that goes against what the manual says, and even then, I would not know where to plug the esc into the fbl.
EXI450DUDE is offline        Reply With Quote Quick reply to this message
Old 10-24-2017, 03:12 PM   #6 (permalink)
Registered Users
 
Posts: 6,437
 
My HF Map location
Join Date: Mar 2009
Location: Samish Island, WA
Default

Quote:
plug the esc into the mini kabr
Yours is apparently not a Mikado product, so this is not the appropriate place to seek support...
GregCA likes this.
__________________
AMA 373608
Citizen #97
K2Freak is online now        Reply With Quote Quick reply to this message
Old 10-24-2017, 05:09 PM   #7 (permalink)
Registered Users
 
Posts: 2,374
 

Join Date: Mar 2011
Location: Gillette, WY, USA
Default

I thought you were using single line. You won’t get throttle using standard rx you have to plug esc into rx unless you use a single line protocol like S-Bus or Spektrum sat.


Sent from my iPhone using Tapatalk
tshelby73 is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © VerticalScope Inc. All rights reserved.
 

SEO by vBSEO 3.6.1