Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Electronics Support > Mikado V-BAR


Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support


Reply
 
LinkBack Thread Tools Display Modes
Old 04-23-2019, 04:31 PM   #1 (permalink)
Registered Users
 
My HF Map location
Join Date: Mar 2007
Default vbar initial programming questions

Following vstabi initial programing instructions and have some questions.
"It says after successful initialization the connection status will switch to green bar and the V will begin to blinking slowly"
Mine stays solid green no blink. And on the transmitter page of the setup wizard, the wizard does not recognise any inputs from aileron--elevator--rudder but the collective work just fine. Sorry first time setup and new to all this, can some one help?

Using dx7 radio and a standard receiver
peterel is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 04-23-2019, 04:57 PM   #2 (permalink)
Registered Users
 
Posts: 7,666
 
My HF Map location
Join Date: Mar 2009
Location: Samish Island, WA
Default

For starters, ensure that you have single servo swash selected and that you chose the correct type of receiver. When you get to the transmitter page you should see all of the controls doing something.

You may need to break it down for us a little so that we can be of more help. Examples: provide further info on your motor, ESC, wiring connections, specific software of your vbar, which governor you will use, etc.
__________________
AMA 373608
Citizen #97
K2Freak is offline        Reply With Quote Quick reply to this message
Old 04-23-2019, 05:55 PM   #3 (permalink)
Registered Users
Thread Starter Thread Starter
 
My HF Map location
Join Date: Mar 2007
Default

Sorry stock 450 trex pro , DX7 radio with AR610 receiver don't know what software and no governor ( that I know of). DX7 set to [ swash type ] --1 servo--norm
Receiver wiring
THRO---comes from esc
AILE--goes to RXA on vbar
ELEV-- '' ''
RUDDER " "
GEAR goes to RXC on vbar
AUX1 goes to RXB on vbar

When I get to transmitter page it only sees the collective. Maybe radio not set right?
peterel is offline        Reply With Quote Quick reply to this message
Old 04-23-2019, 10:13 PM   #4 (permalink)
Registered Users
 
Posts: 10,407
 
My HF Map location
Join Date: Sep 2007
Default

https://www.vstabi.info/en/node/436

Work your way through the setup procedure in the link above. when finished with the page, click on the right bottom link to go to next step. TX setup and wiring is all there.
__________________
Gaui R5, Henseleit TDR, TDR2, TDF, TDS
Kontronik, Scorpion ESC, iChargers, VBar,
VControl
Old hand at Planks
Vinger is offline        Reply With Quote Quick reply to this message
Old 04-23-2019, 10:20 PM   #5 (permalink)
Registered Users
Thread Starter Thread Starter
 
My HF Map location
Join Date: Mar 2007
Default

Been there, done that, 3 times. Still the same thing. I'm thinking that I may have shorted the vbar out some how.
peterel is offline        Reply With Quote Quick reply to this message
Old 04-24-2019, 09:08 AM   #6 (permalink)
Registered Users
 
Posts: 10,407
 
My HF Map location
Join Date: Sep 2007
Default

RX A is a triple INPUT plug and should have the single signal wires from AILERON. ELEV and RUDDER into it. Make sure you have the correct wire from the RX channels, normally white or yellow in color.

RD = Tail rotor servo
Ch1 ... 3 = Swashplate servos
RX A = Aileron, elevator and rudder signal from RX
RX B = Collective RX signal and power supply
RX C = Gyro gain RX signal and power supply
RX 1 = not used
RX 2 = not used

If you had power into RX A even for a brief period then the VBar is toast.

https://www.vstabi.info/en/node/442
__________________
Gaui R5, Henseleit TDR, TDR2, TDF, TDS
Kontronik, Scorpion ESC, iChargers, VBar,
VControl
Old hand at Planks
Vinger is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

SEO by vBSEO 3.6.1