Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Electronics Support > BeastX FBL System


BeastX FBL System BeastX FBL Flybarless System Software and Hardware Support


Like Tree1Likes
Reply
 
LinkBack Thread Tools Display Modes
Old 03-09-2015, 10:49 AM   #341 (permalink)
Registered Users
 
Posts: 1,785
 

Join Date: Mar 2011
Default

The light is to tell you that you are either setting positive or negative pitch. Blue for negative, red for positive.
__________________
MSH, Cyclone
Way2evl is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 03-09-2015, 01:56 PM   #342 (permalink)
Registered Users
 
Posts: 1,785
 

Join Date: Mar 2011
Default

Quote:
Originally Posted by Bladecpnitro View Post
Where does the BeastX like to have the ball set on say a 450?
I had all the tail blowing dialed out with a GT 5 and now with a Beastx I'm blowing the tail again on hard maneuvers and cross wind conditons?

The GT 5 liked the ball to be out farther than most gyros so I'm thinking I need to move the ball in and bump up the tail gain a little. With current mechanical gain on rudder I can bump gyro gain to 75% and the tail holds well in FB flight and tail down funnels but I get ocassional tail shake in fast forward circuits.

Thanks!
Adjust your gain in small movements. Seems like you have it really close. Seems like you have the ball set in a good hole also. Let us know if it still blows out after you get the wag taken care of.
__________________
MSH, Cyclone
Way2evl is offline        Reply With Quote Quick reply to this message
Old 03-16-2015, 06:31 PM   #343 (permalink)
Registered Users
 

Join Date: Jun 2014
Default

Quote:
Originally Posted by Way2evl View Post
The light is to tell you that you are either setting positive or negative pitch. Blue for negative, red for positive.
Ah well that explains it!!! Thanks!
floatingkiwi is offline        Reply With Quote Quick reply to this message
Old 05-31-2015, 06:13 PM   #344 (permalink)
Registered Users
 
Posts: 5,096
 

Join Date: Mar 2011
Default

When changing parameter E, does dead band increase or decrease as you move to the right in the manual?

I had that set to Purple which I assume was almost no dead band, is this correct? I set it to Red

B- Control Behavior is set to TX 120 ail-ele endpoints
C- Pitching Up - works great at Red default
G- Cyclic Responce- I reduced it from high- blue flashing- to red which enabled me to set my #1 Pot back in the middle instead of 10 0clock.

H - Pitch Boost - I set to Red as well to give it a tad more pitch pop.

I got 5 flights on it and it feels better in every way, not quite as much cyclic as I had so might need to bump G menu back up or just reduce expo a little as a still have a good flip rate at full stick.

I had the 450 Pro flying well with the exception of a slow cyclic bounce back on hard flips and crappy hesitating tictocs and piro flips and a soft mushy collective.
__________________
If its fixed don't break it!
Bladecpnitro is offline        Reply With Quote Quick reply to this message
Old 06-16-2015, 09:42 AM   #345 (permalink)
Registered Users
 
Posts: 357
 
My HF Map location
Join Date: Jun 2006
Default

Quote:
Originally Posted by Bladecpnitro View Post
I had that set to Purple which I assume was almost no dead band, is this correct? I set it to Red
Hi,

yes that's correct. Purple is the smallest value, very little deadband, and then it increases stepwise up until blue which gives a lot of deadband.
__________________
best regards from Germany
Stefan
BEASTX r&d Team
freakware.com
Frenchdress is offline        Reply With Quote Quick reply to this message
Old 07-19-2020, 01:53 PM   #346 (permalink)
Registered Users
 

Join Date: Oct 2012
Default Is there a tuning guide for 5.0?

I assume this tuning guide will work just the same? is there anything in particular to look out for?
__________________
- VultAge -

470LT, G420, G570, Chronos, T-Rex 600N and 700N
vultage is offline        Reply With Quote Quick reply to this message
Old 12-10-2020, 03:51 PM   #347 (permalink)
Registered Users
 
Posts: 341
 

Join Date: Mar 2006
Default v5.

http://www.beastx.com/download/manua...719_web_EN.pdf
__________________
I made a mistake once, but I was wrong...
tommytt1 is offline        Reply With Quote Quick reply to this message
Old 12-10-2020, 03:55 PM   #348 (permalink)
Registered Users
 
Posts: 341
 

Join Date: Mar 2006
Default v 5.2 Wiki

https://wiki.beastx.com/index.php/Ma...blV52:Intro/en
__________________
I made a mistake once, but I was wrong...
tommytt1 is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.

SEO by vBSEO 3.6.1