START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Multi Rotor Helicopters - Tandem Multi Rotor Helicopters - Tandem |
|
LinkBack | Thread Tools | Display Modes |
07-19-2013, 07:12 AM | #1 (permalink) |
Registered Users
Join Date: Apr 2004
|
KK2 help
I have a kk2 board I purchased and I am getting no signal on all the channels from the receiver test menu. Futaba radio equipment and the unit is bound fine because I can power and run servos no problem. I can cal the gyro and set and adjust everything but the ESC and rec.
Any thoughts? Thanks
__________________
Tim Tripoli Team Futaba, Rail Blades Team crash ProgressiveRC |
Sponsored Links | |||
Advertisement |
|
07-19-2013, 08:13 AM | #2 (permalink) |
HF MR Support
Join Date: Aug 2008
|
Does the KK2 light up? Try scrolling to the end and debug.....
__________________
Gaui 550(Need GOT ONE!) / KK2.1.5 steveis pro/ZMR250 / Alien 450 camera ship / HJ 450 all W/KK2.1.5 Steveis pro Estes Nano/ Hubsan X4 / Syma X1 AMA 953414 CONTRIBUTOR, TEAM LAVAQUAD |
07-19-2013, 09:48 AM | #3 (permalink) |
Registered Users
Join Date: Aug 2012
|
Try powering up the receiver for a second, then power the KK2 up.
|
07-19-2013, 10:07 AM | #4 (permalink) |
HF MR Support
Join Date: Aug 2008
|
...frame rate for Futaba?
Have never seen a KK2 not link up....
__________________
Gaui 550(Need GOT ONE!) / KK2.1.5 steveis pro/ZMR250 / Alien 450 camera ship / HJ 450 all W/KK2.1.5 Steveis pro Estes Nano/ Hubsan X4 / Syma X1 AMA 953414 CONTRIBUTOR, TEAM LAVAQUAD |
07-19-2013, 10:24 AM | #5 (permalink) |
Registered Users
Join Date: Aug 2012
|
This was a common problem with older firmware.
I would make sure to update to the 1.6 firmware too. |
07-19-2013, 12:15 PM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2004
|
Firmware is 1.6
Yes the unit powers on fine and all menu are accessible. I will try powering the receiver first when I get home tonight. Thanks for the suggestions so far.
__________________
Tim Tripoli Team Futaba, Rail Blades Team crash ProgressiveRC |
07-19-2013, 12:29 PM | #7 (permalink) |
Registered Users
Join Date: Aug 2012
|
Also be sure that CPPM is disabled in the KK2 menu.
|
07-19-2013, 12:35 PM | #8 (permalink) |
HF MR Support
Join Date: Aug 2008
|
...Agreed!
__________________
Gaui 550(Need GOT ONE!) / KK2.1.5 steveis pro/ZMR250 / Alien 450 camera ship / HJ 450 all W/KK2.1.5 Steveis pro Estes Nano/ Hubsan X4 / Syma X1 AMA 953414 CONTRIBUTOR, TEAM LAVAQUAD |
07-19-2013, 03:47 PM | #9 (permalink) |
Registered Users
Join Date: Sep 2011
|
Unless you are using a FlySky Rx then it makes the install very easy using a single cable and CPPM.
http://www.hobbyking.com/hobbyking/s...ompatible.html
__________________
similis vobis fugere eam furatus "The beatings will continue until morale improves." -- William Bligh |
07-19-2013, 04:40 PM | #10 (permalink) |
Registered Users
Join Date: Aug 2012
|
Well, yeah. CPPM is far cleaner and easier than using standard servo cables. But if he's not using CPPM, he will need to disable it in the menu or else he will get this error.
|
07-20-2013, 06:15 AM | #11 (permalink) |
Registered Users
Thread Starter
Join Date: Apr 2004
|
Thanks guys already for my maiden today.
__________________
Tim Tripoli Team Futaba, Rail Blades Team crash ProgressiveRC |
07-20-2013, 11:25 AM | #12 (permalink) |
HF MR Support
Join Date: Aug 2008
|
...Video please!
__________________
Gaui 550(Need GOT ONE!) / KK2.1.5 steveis pro/ZMR250 / Alien 450 camera ship / HJ 450 all W/KK2.1.5 Steveis pro Estes Nano/ Hubsan X4 / Syma X1 AMA 953414 CONTRIBUTOR, TEAM LAVAQUAD |
Thread Tools | |
Display Modes | |
|
|