Register Now

mrultralite · 04-08-2012, 12:57 PM

Yes, I'm using the GT5 also. "0.035 / 0.050" are for the servo speed... but careful, the GT5 applies this value per 45 degrees, whereas servo manufacturer usually gives you for 60 degrees.

Thanks Zb !

i've been scratching my head on that one! Stoopid 1/2 info !
Oh and to add to the confusion it was called 'delay' not rate , why not just call it speed

vic7322 · 04-16-2012, 07:47 AM

can someone explain this again?? I think my delay is off for my ds650 and its causing drift issues

mrultralite · 04-16-2012, 09:34 PM

The GT5 has a setting called 'delay' in the servo menu. Go to the servo manufacturs website and look up servo speed for your servo, then recalculate from 60 to 45 proportionately.

vic7322 · 04-16-2012, 10:05 PM

AH Thank You....
Motion speed: 0.058sec/60°(4.8V), 0.048sec/60°(6.0V)
Im gonna try running .036 on 6v. Hopefully that will help solve my tail drift issues

NitroAl · 04-19-2012, 09:35 AM

Increase the deadband! Set the delay too low could damage the servo!

mrultralite · 04-19-2012, 11:04 AM

Al, But whats too low? mystery here is finding right setting in an information vacuum. Whats the right deadband setting?

vic7322 · 04-19-2012, 03:38 PM

Im confused, What dead band for the tail are you talking about... Is it in the P/I menu? or is it in the menu that looks like a tx stick?? Should I increase the dead band so the servo is not always adjusting?

mrultralite · 04-19-2012, 08:58 PM

Easiest way to find this stuff is the 'configurations table' sheet that comes with the unit. Tail DB is in the P/I tail menu.

NitroAl · 04-20-2012, 02:41 AM

As Mrultralite has pointed the configurations table can be a useful guide! In the second column under E720 they cover the SV1258TG and SV1290MG which are the Savox versions of the DS610 and DS650 and also the Spektrum H6040 and whatever there tail servo is. So on some settings the answers are all there ;-)

MLC1 · 04-22-2012, 12:57 PM

I am running the Align servo's. I went thru and reset them to the E720>SV servo settings on the configuarations table. I am now at .045/.050 and the SU Fre was bumpped down to 166. Seems to fly ok.

How would you calculate this if they setting were not availble?

mrultralite · 04-22-2012, 09:28 PM

The GT5 has a setting called 'delay' in the servo menu. Go to the servo manufacturs website and look up servo speed for your servo, then recalculate from 60 to 45 proportionately.

Oilsands · 04-23-2012, 09:35 AM

To calculate the speed I took the spec given for 60, devided by 60 then multiplied by 45.
So as an example: if I had a servo that had 0.18/60 degree at 4.8 v, then I would take 0.18 devided by 60 then multiplied by 45 = value to enter.

Oilsands · 04-23-2012, 11:16 AM

Quote:

Originally Posted by vic7322

AH Thank You....
Motion speed: 0.058sec/60°(4.8V), 0.048sec/60°(6.0V)
Im gonna try running .036 on 6v. Hopefully that will help solve my tail drift issues

Yes, max of .045 at 4.8 v or .036 at 6 v

04-08-2012, 12:57 PM	#1 (permalink)
mrultralite Registered Users Join Date: Jun 2011	'Delay" setting mystery explained Yes, I'm using the GT5 also. "0.035 / 0.050" are for the servo speed... but careful, the GT5 applies this value per 45 degrees, whereas servo manufacturer usually gives you for 60 degrees. Thanks Zb ! i've been scratching my head on that one! Stoopid 1/2 info ! Oh and to add to the confusion it was called 'delay' not rate , why not just call it speed Last edited by mrultralite; 04-16-2012 at 09:35 PM..

04-19-2012, 09:35 AM	#5 (permalink)
NitroAl Registered Users My HF Map location Join Date: Jun 2008	Increase the deadband! Set the delay too low could damage the servo! __________________ CustomHeliParts/KDE TRex 700N ThunderTiger X50 FBL Ely.Q Vision 90 Ely.Q Vision 50

04-20-2012, 02:41 AM	#9 (permalink)
NitroAl Registered Users My HF Map location Join Date: Jun 2008	As Mrultralite has pointed the configurations table can be a useful guide! In the second column under E720 they cover the SV1258TG and SV1290MG which are the Savox versions of the DS610 and DS650 and also the Spektrum H6040 and whatever there tail servo is. So on some settings the answers are all there ;-) __________________ CustomHeliParts/KDE TRex 700N ThunderTiger X50 FBL Ely.Q Vision 90 Ely.Q Vision 50

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-16-2012, 07:47 AM	#2 (permalink)
vic7322 Registered Users Join Date: Oct 2009	can someone explain this again?? I think my delay is off for my ds650 and its causing drift issues

04-16-2012, 09:34 PM	#3 (permalink)
mrultralite Registered Users Thread Starter Join Date: Jun 2011	The GT5 has a setting called 'delay' in the servo menu. Go to the servo manufacturs website and look up servo speed for your servo, then recalculate from 60 to 45 proportionately.

04-16-2012, 10:05 PM	#4 (permalink)
vic7322 Registered Users Join Date: Oct 2009	AH Thank You.... Motion speed: 0.058sec/60°(4.8V), 0.048sec/60°(6.0V) Im gonna try running .036 on 6v. Hopefully that will help solve my tail drift issues

04-19-2012, 11:04 AM	#6 (permalink)
mrultralite Registered Users Thread Starter Join Date: Jun 2011	Al, But whats too low? mystery here is finding right setting in an information vacuum. Whats the right deadband setting?

04-19-2012, 03:38 PM	#7 (permalink)
vic7322 Registered Users Join Date: Oct 2009	Im confused, What dead band for the tail are you talking about... Is it in the P/I menu? or is it in the menu that looks like a tx stick?? Should I increase the dead band so the servo is not always adjusting?

04-19-2012, 08:58 PM	#8 (permalink)
mrultralite Registered Users Thread Starter Join Date: Jun 2011	Easiest way to find this stuff is the 'configurations table' sheet that comes with the unit. Tail DB is in the P/I tail menu.

04-22-2012, 12:57 PM	#10 (permalink)
MLC1 Registered Users Join Date: Mar 2009	I am running the Align servo's. I went thru and reset them to the E720>SV servo settings on the configuarations table. I am now at .045/.050 and the SU Fre was bumpped down to 166. Seems to fly ok. How would you calculate this if they setting were not availble?

04-22-2012, 09:28 PM	#11 (permalink)
mrultralite Registered Users Thread Starter Join Date: Jun 2011	The GT5 has a setting called 'delay' in the servo menu. Go to the servo manufacturs website and look up servo speed for your servo, then recalculate from 60 to 45 proportionately.

04-23-2012, 09:35 AM	#12 (permalink)
Oilsands Registered Users Join Date: Aug 2010	To calculate the speed I took the spec given for 60, devided by 60 then multiplied by 45. So as an example: if I had a servo that had 0.18/60 degree at 4.8 v, then I would take 0.18 devided by 60 then multiplied by 45 = value to enter.

Register Now

Log-in