 |
START HERE |
|
| Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
|
|
|
Unregistered
|
||||||
| Futaba Radios and Electronics Futaba Radios, Gyros, Servos, Etc. |
|
|
 |
|
|
LinkBack | Thread Tools | Display Modes |
10-13-2007, 10:54 AM
|
#1 (permalink) |
|
Join Date: Sep 2007
|
Futaba 9CH Super and R9SDP Reciever Help
I was trimming the heli and then i messesed something up so i reset the transmitter and now i get no movement on any of the servos. Please help.
|
|
|
| Sponsored Links | |||
|
Advertisement |
|
||
|
10-14-2007, 12:24 PM
|
#2 (permalink) |
|
Registered Users
|
when you said you 'reset the transmitter', you turned it off? go back to the model you were working on and scroll through the settings...take a look at pcm/ppm setting...might have changed...
-ken
__________________
Logo10-3D(Stretch)|HackerC50-14L|14T|Jazz55-10-32|6S|A123|JR368|GY401/9254|Fut9CHPS2.4 Logo10Deluxe(Stretch)|Orbit20-10|21T|Schulze18.61|6S|A123|Fut9650|GY401/9254|R148DP Raptor30V2-OS37-HatoriSAB-6RS | Raptor50V2-OS50 Hyper-CY MP5 | Gaui Hurricane200 | Kaos40-SJ50 | US1000-OS1.60FX | AW Yak54-90/120-MLD28 | GP Reactor1.60-DA50R | |
|
|
|
|
10-16-2007, 10:50 AM
|
#3 (permalink) |
|
Thread Starter
Join Date: Sep 2007
|
no,I reset the parameters, like I reset all the settings to factory.. and now nothing works, no servo movement or anything.
|
|
|
|
|
10-16-2007, 12:38 PM
|
#4 (permalink) |
|
Registered Users
|
i use a 9chps for my raptors, but i'm not too good at explaining the setup--even to myself! this link is very good, and includes the 9c for each step of the transmitter setup...hope it helps...ken
http://www.raptortechnique.com/radiosetup.htm
__________________
Logo10-3D(Stretch)|HackerC50-14L|14T|Jazz55-10-32|6S|A123|JR368|GY401/9254|Fut9CHPS2.4 Logo10Deluxe(Stretch)|Orbit20-10|21T|Schulze18.61|6S|A123|Fut9650|GY401/9254|R148DP Raptor30V2-OS37-HatoriSAB-6RS | Raptor50V2-OS50 Hyper-CY MP5 | Gaui Hurricane200 | Kaos40-SJ50 | US1000-OS1.60FX | AW Yak54-90/120-MLD28 | GP Reactor1.60-DA50R | |
|
|
|
|
10-16-2007, 02:16 PM
|
#5 (permalink) |
|
Registered Users
|
Go into the Parameter menu and make sure modulation is set to PCM, if you have to change it, power cycle the transmitter then try it.
|
|
|
|
|
10-16-2007, 09:02 PM
|
#6 (permalink) |
|
Thread Starter
Join Date: Sep 2007
|
thank you for the advice, i will try it as soon as i get the Rx battery charged up again. For a T-Rex 600, what should the "type" be set to on the transmitter??...sorry for all these questions, i'm new at this and i'm still loking for someone to help me. (thank god for theses forums)
|
|
|
|
|
10-17-2007, 09:53 PM
|
#8 (permalink) |
|
Thread Starter
Join Date: Sep 2007
|
Andy, thank you so much for that information. It worked. Anyway, i charged the Rx battery so that i can finish trimming the heli and when i turned on the bec, the lights came on the went of and now it will not turn on anymore. could i have burned it out?...i hope not
|
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
