START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
YGE YGE ESC Support and Discussion |
|
LinkBack | Thread Tools | Display Modes |
07-04-2014, 11:28 AM | #1 (permalink) |
Registered Users
Join Date: Sep 2011
|
YGE 160HV Unable to Learn Max RPM in Gov Store Mode
Hi folks, need some advice here.
I have purchased the YGE prog card to program the YGE 160HV that came with the Logo Xxtreme. Did the throttle end point settings then went ahead with programming the esc using the program card .... everything went on well. Charge my batts to 4.05V, plug in batteries and got the continuous single beep sound as per MrMel's video upon powering up. Push the stick to 100% but nothing happens. The motor kept spinning and the esc did not achieve learning even after 30 seconds. I have tried a few times and it did not work as per MrMel's video. I have a few YEP 180HV esc and have set all of them per MrMel's video and none of them had the same issue.
__________________
Nothing smaller than 700 ..... |
Sponsored Links | |||
Advertisement |
|
07-04-2014, 04:43 PM | #2 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
Oh another thing, after spinning to learn, the continuous single beep sound did not go away and continue to be present at every power up.
__________________
Nothing smaller than 700 ..... |
07-04-2014, 05:35 PM | #3 (permalink) |
Registered Users
Join Date: Feb 2013
|
this is the mikado version yge video from mr.mel
[ame]http://youtu.be/brBmmff669Y[/ame]
__________________
|
07-04-2014, 10:39 PM | #4 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
Hi that was the video i followed for all my previous yep and they are all properly setup but the yge it does not work.
__________________
Nothing smaller than 700 ..... |
10-06-2016, 09:29 PM | #5 (permalink) |
Registered Users
Join Date: Oct 2007
|
Having the same issue. Did you resolve it?
|
10-06-2016, 10:53 PM | #6 (permalink) |
Registered Users
Join Date: Oct 2007
|
Have the same issue. Did you resolve it?
|
10-16-2016, 10:38 AM | #7 (permalink) |
Registered Users
Join Date: Nov 2013
|
Did you get this fixed ? Did you verify that it actually learned the endpoints correctly when you did stick up and stick down on boot up etc.
In my case YGE 200, I did that endpoints learn but I had to go back and increase the max endpoint in my transmitter by 5 pts or so and then it would learn gov store. When you are trying to learn gov store and you observe that you are not getting the hiccup to tell you it learned, you should watch the orange led on the esc, which is supposed to go out completely when you get the hiccup, indicating full power. This was not happening on mine. Until I raised the endpoints. I have no clue why there is no one from YGE helping the users. As the instructions it comes with are good for toilet paper and the videos online are from countless firmware versions ago. Its all out dated. For the record, still my favorite esc. |
10-16-2016, 11:49 AM | #8 (permalink) |
Registered Users
Thread Starter
Join Date: Sep 2011
|
The xxtreme ver yge comes with a firmware that disallow certain setup from the proj card. I set the esc up with some settings from vstabi website and switch back to vbar gov instead of gov store.
__________________
Nothing smaller than 700 ..... |
Thread Tools | |
Display Modes | |
|
|