Register Now

zr1100 · 07-19-2017, 04:22 PM

Wonder what radio system receivers (Spektrum ?) work with Naza.
I see s-bus on quick-guide (Futaba)--does that mean Jeti would also work (Ex-bus)?

Is the Naza BEC needed, or do normal heli ESC's with built-in BEC work?

Thanks very much

TACO88 · 07-20-2017, 09:12 AM

I have used a FrySky radio with my Naza H and right now am using a JR XG11 DMSS. I don't use the Naza BEC, I'm using a 2S LiFePo4 battery to power my electronics. Normal BEC from the ESC should work just fine.

99100 · 07-20-2017, 10:05 AM

Im using a spektrum or lemon (same but different)

StripedGear · 07-21-2017, 09:38 PM

If your using servos that can run on 6 volts then you can use the esc bec set at 6 volts and there will be no issue. If your using servos rated at 5 volts then you will need an external bec that you can set to 5.6 / 5.8 volts constant. Otherwise at 5 volts along with system current draw that will fluctuate a 0.5 volts. the low voltage trigger [4.8] will reboot the naza while in flight. Bad news CRASH.
So to be safe 5.8 or higher is best.

07-19-2017, 04:22 PM	#1 (permalink)
zr1100 Registered Users Join Date: Feb 2016	Naza-H Receivers/BEC ?? Wonder what radio system receivers (Spektrum ?) work with Naza. I see s-bus on quick-guide (Futaba)--does that mean Jeti would also work (Ex-bus)? Is the Naza BEC needed, or do normal heli ESC's with built-in BEC work? Thanks very much

07-20-2017, 10:05 AM	#3 (permalink)
99100 Registered Users Join Date: Mar 2015	Im using a spektrum or lemon (same but different) __________________ 700N MJ DTS VX1N, Logo 690SX - VX1e, 780L Top - VBar Neo, 700L Top - VX1n, Logo 550SX - VX1n, Goblin 570 (6s) - VX1n, Trex 550E Pro DFC - VX1n, Trex 450L Dominator (6s) - VX1n, Trex 450 Plus DFC - VX1n, JETI, DX9, Pheonix R/C, AccuRC, neXt

07-21-2017, 09:38 PM	#4 (permalink)
StripedGear Registered Users Join Date: Feb 2012	If your using servos that can run on 6 volts then you can use the esc bec set at 6 volts and there will be no issue. If your using servos rated at 5 volts then you will need an external bec that you can set to 5.6 / 5.8 volts constant. Otherwise at 5 volts along with system current draw that will fluctuate a 0.5 volts. the low voltage trigger [4.8] will reboot the naza while in flight. Bad news CRASH. So to be safe 5.8 or higher is best. __________________ Dennis Dube http://pcrcheliclub.com Roban 700 Super Scale AS350, Century Bell 206 Jet Ranger Trex 600, Spektrum DX8

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-20-2017, 09:12 AM	#2 (permalink)
TACO88 Registered Users Join Date: Feb 2005	I have used a FrySky radio with my Naza H and right now am using a JR XG11 DMSS. I don't use the Naza BEC, I'm using a 2S LiFePo4 battery to power my electronics. Normal BEC from the ESC should work just fine.

Register Now

Log-in