 |
START HERE |
|
| Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
|
|
|
Unregistered
|
||||||
| 2.4G JR Radios JR 2.4 Gigahertz Radios and Technology |
|
|
 |
|
|
LinkBack | Thread Tools | Display Modes |
02-20-2016, 10:33 AM
|
#1 (permalink) |
|
Registered Users
Join Date: May 2011
|
Telemetry sensor
I just had a mist pleasant experience today haing the Unisens-e sensor.
It took me a grand total of 30 min to soldier EC5 connectors and to set up the parameters via the USB cable and when I turned on my system all the desired values were displayed on transmitter. It was a really pleasant and worry free experience and my XG11 displayed all parameters without any hustle. Took out the helicopter today (I fly scale only) and it displayed the correct values without any issues. I know the RPM setup (CC ESC governor mode) and i guestimated the hight. I pulled a log after the flight and to my best knowledge the values displayed on the screen were true. I'm a happy camper today and I just had to share this.... Gh |
|
|
| Sponsored Links | |||
|
Advertisement |
|
||
|
02-22-2016, 10:50 AM
|
#2 (permalink) |
|
Registered Users
Join Date: Mar 2012
|
I use the same setup in my 700. Flying to mah consumption with pack voltage warnings is sweet.
I also set a alarm on the loss of telemetry. So most anything going wrong will set off one of the alarms I have. Radio beeps. Auto in for a landing and check it out!!!
__________________
Team JR Americas Synergy Helicopters Rail Blades Scorpion Motors |
|
|
|
|
03-02-2016, 01:49 PM
|
#3 (permalink) |
|
Registered Users
Join Date: Jan 2008
|
i like but no us distributor ??
__________________
Trex_600n,Trex_500,MR25,MikadoLoGo5003D_KDE,CastleCreations,Ys,JR XG8,Sab Goblin 380/X_Nova/Bk_Servos, JR TagsMini//Sab Goblin 500Pulse Edition, Sab Goblin570Carbon_SABUSA_X_Nova_BkServos_KDE,RJX-Swash,JR-SPG-Tail/TagsMini_JRX-Bus. |
|
|
|
|
03-03-2016, 09:23 AM
|
#4 (permalink) |
|
Registered Users
Thread Starter
Join Date: May 2011
|
That I don't know. But seeing that there is a significant number if Jlog units that move through the classifides section I would assume that there is a US distributor....
Gh |
|
|
|
|
03-16-2016, 08:52 PM
|
#5 (permalink) |
|
Registered Users
Join Date: Jun 2014
|
Are you guys using one of these sensors only for a 12s 700 setup? (one unisensor going to a 6s pack) Any more information would be appreciated.
__________________
Synergy 766, Goblin 700C, Synergy E7 SE, Logo 700, Align 700x, Logo 550sx, Goblin 500, Oxy3 TE, BK Servos, Spartan VX1e, TX - JR XG14 Xbus |
|
|
|
|
03-16-2016, 11:42 PM
|
#6 (permalink) |
|
Registered Users
|
It fits between the pack and your ESC and you get different versions according to max amperage draw.
http://www.sm-modellbau.de/shop/index.php?cPath=18
__________________
Henseleit TDR, TDR2, TDF, TDS, TDSF Kontronik, Scorpion ESC, iChargers, VBar, VControl Old hand at Planks  Peter |
|
|
|
|
03-18-2016, 01:50 AM
|
#7 (permalink) |
|
Registered Users
Thread Starter
Join Date: May 2011
|
It works on 6S as well....
gh |
|
|
|
|
06-20-2016, 08:16 PM
|
#8 (permalink) |
|
Registered Users
Join Date: Jun 2014
|
So I am trying to buy one of these. https://www.sm-modellbau.de/UniSens-E-und-Zubehoer
This site doesnt seem to ship to the US? My German is well terrible but none of the "Land" which I am seeing is country is the USA. What other distributor is there to order these to the US? Thanks, -Cory
__________________
Synergy 766, Goblin 700C, Synergy E7 SE, Logo 700, Align 700x, Logo 550sx, Goblin 500, Oxy3 TE, BK Servos, Spartan VX1e, TX - JR XG14 Xbus |
|
|
|
|
06-21-2016, 05:51 AM
|
#9 (permalink) |
|
Registered Users
Thread Starter
Join Date: May 2011
|
use the "kontakt" link at the bottom
also get the USB link as well https://www.sm-modellbau.de/USB-Interface as you'll need to adjust the parameters in the unit... gh |
|
|
|
|
06-21-2016, 08:33 AM
|
#10 (permalink) |
|
Registered Users
Join Date: Jun 2014
|
Thanks I ended up emailing them and the US is " Vereinigte Staaten". I ordered 2 - 1 for each Synergy and 1 USB module - I am exited I hope it works as good as I am expecting.
__________________
Synergy 766, Goblin 700C, Synergy E7 SE, Logo 700, Align 700x, Logo 550sx, Goblin 500, Oxy3 TE, BK Servos, Spartan VX1e, TX - JR XG14 Xbus |
|
|
|
|
06-21-2016, 12:30 PM
|
#11 (permalink) |
|
Registered Users
Thread Starter
Join Date: May 2011
|
you will be pleasently surprised...
gh |
|
|
|
|
07-12-2016, 08:12 AM
|
#12 (permalink) |
|
Registered Users
Join Date: Jun 2014
|
I wanted to update this thread. I've installed the 280 amp unisens-e unit on my 766 and last night my E7 SE. It works great!!! I was very nervous about the 6.5mm bullets as redundant joints on the system but my soldering was good and the 766 wires come down normal in temperature.
I posted the update in my 766 discussion thread on the Synergy forum. Now I need to order 1 more for my G700c. 
__________________
Synergy 766, Goblin 700C, Synergy E7 SE, Logo 700, Align 700x, Logo 550sx, Goblin 500, Oxy3 TE, BK Servos, Spartan VX1e, TX - JR XG14 Xbus |
|
|
|
|
07-12-2016, 08:49 AM
|
#13 (permalink) |
|
Registered Users
Thread Starter
Join Date: May 2011
|
Great news....
Gh Sent from my iPhone using Tapatalk |
|
|
|
|
08-18-2016, 09:58 PM
|
#14 (permalink) |
|
Registered Users
|
Has anyone ever started to stock these in North America? I cannot get a translator to work on this site and have no idea what I am seeing or trying to read. seems like such a great product and would love to try out a few on my helis. Seems like a great product for JR Americas to stock really.
__________________
Rycroft Wings & Blades (MAAC Club)Rotor-Tech Blades |
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
