START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Blade 450 Blade 450 Helicopters Information and Help |
|
LinkBack | Thread Tools | Display Modes |
05-08-2012, 05:12 AM | #1 (permalink) |
Registered Users
Join Date: Feb 2012
|
B450
I have some black residue on my main gear and after reading posts which suggested I take out the motor and check something. Anyways when I went to unscrew the screws one them just wouldn't budge so I applied ample amount of pressure til the screw striped at head. Any suggestions on how to remove this screw?
|
Sponsored Links | |||
Advertisement |
|
05-08-2012, 08:14 AM | #2 (permalink) |
Registered Users
Join Date: Feb 2012
|
I had the exact same thing happen last night. There is a tremendous amount of threadlock and adhesive on that motor mount and screws and I stripped one of the screws holding the motor before I got more creative. On the one you haven't stripped, I had luck heating it with a soldering iron to break down the threadlock and then it came out with minimal force.
With regard to the screw that was stripped, someone may have a better suggestion that doesn't destroy the screw, but my solution was to take my dremel and cutting wheel and grind a slot into it to be able to use a larger flat head screwdriver to remove. Be careful doing this as the motor mount is pretty soft aluminum. I ground a slot into it, heated it with a soldering iron to break down the loctite and then was able to remove it with somewhat minimal force. I had a spare hardware set for the heli that had 2 extra screws in it for the motor so I wasn't as worried about destroying one of the screws but I suspect you might not have a choice if it is stripped. It's a good thing to check it was a bearing that had seized on the shaft and was causing the residue. Good luck. |
05-08-2012, 02:37 PM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Feb 2012
|
Thanks for that Chris next time I head to the Hobby store I like ask them, as I still to purchase new screws for it. so I will just fly it like this for the time being.
|
05-08-2012, 07:57 PM | #4 (permalink) |
Registered Users
Join Date: Apr 2011
|
All right, that does it. I'm starting yet another heli blog since so many reoccurring events and problems keep getting brought up. Might be too late for yours but I went to the hardware store and hobby shop for the real small stuff to invest in quality wrenches. I own a couple dremels and almost went drilling away but thought I'd try a different wrench set first and to my amazement it came right out even though one was a little stripped. For as soft as the screws are, I think the keys that came with the heli are softer.
|
05-09-2012, 12:16 AM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Feb 2012
|
I just may try that
|
05-09-2012, 12:34 AM | #6 (permalink) |
Registered Users
|
Yup
I did it, I stripped one of the screws trying to get it out. I grabbed it with a large set of pliers
and unscrewed it. Flattened out that shiny little washer thing as well. Now I will have to find a new one. I'm sure I will have to dish out $50.00 on a rebuild kit!
__________________
Ron Petrolia Ontario Canada. Electric, MCPX-BL,450X, Trex 550E Nitro Hirobo SCEADU Evolution 50 |
05-09-2012, 04:10 AM | #7 (permalink) | |
Registered Users
Thread Starter
Join Date: Feb 2012
|
Quote:
|
|
10-18-2012, 09:36 AM | #8 (permalink) |
Registered Users
Join Date: Oct 2012
|
Black residue on main gear
Did you find out what was causing the black residue? I suspected it was from the belt drive. Is it normal?
|
10-18-2012, 07:34 PM | #10 (permalink) |
Registered Users
Join Date: Feb 2012
|
FYI the easiest way to get these screws out is to heat up the screw by setting a soldering iron on the head for about 30 seconds, then using good tools (like dynamite or similar) turn out the screw. This may take more than 1 heat cycle since the thread locker will set up as it cools. I removed the ESC and slightly drilled the corners of the frame to allow a straight shot at the screws.
Hope this helps somebody!
__________________
Lynx Heli Innovations Team Pilot "I do my best looking 3d when trying to avoid a crash!" |
Thread Tools | |
Display Modes | |
|
|