Step G still not sure how to save properly - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Electronics Support > BeastX FBL System


BeastX FBL System BeastX FBL Flybarless System Software and Hardware Support


Reply
 
LinkBack Thread Tools Display Modes
Old 07-15-2012, 01:13 PM   #1 (permalink)
Registered Users
 
Posts: 370
 

Join Date: Jan 2011
Location: Vancouver Canada
Default Step G still not sure how to save properly

Should I leave Step G at one of the servos (with light on ) or at reference point (light off ) or it doesn't matter ??? thanks !
__________________
Trex450Pro BeastX
Trex550E HC3SX
Trex700E HC3SX
JR11X
bladesr is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 07-15-2012, 01:20 PM   #2 (permalink)
Registered Users
 
Posts: 10,715
 

Join Date: Apr 2011
Location: Seattle, Wa
Default

Doesn't matter


Sent from my iPhone using Tapatalk
__________________
Heli's I have:
Goblin 500 (Vbar Neo), Gaui X5(Vbar Neo), X7(Vbar Neo) Vbar Vcontrol
I'm the not so newbheliusr as I have been here a while. But I like this name.
newbheliusr is online now        Reply With Quote Quick reply to this message
Old 07-15-2012, 01:35 PM   #3 (permalink)
Registered Users
 
Posts: 10,180
 
My HF Map location
Join Date: Feb 2008
Location: Manchester, England
Default

+1, it doesn't matter. This having been said, there is a small advantage with moving on whilst one of the servo lights is on. This way you can definitely see that you are moving on whilst all the servos are in their adjusted positions. If you had missed one it would be obvious. Since all will be out, to some extent, when in the reference position, and all will move to the adjusted positions when you press the button to move on, it perhaps isn't so obvious if one has been missed. Or maybe it would still be obvious.

I assume you have a reason for asking? Are you having some trouble getting it to store the changes you make at G?

Cheers

Sutty
__________________
Regards, Sutty
BeltEXI, mCX, mSR, 4G3, FBL Trex250SE ÁB, FBL Trex450Pro ÁB,
FBL Trex550e VX1 Pro, FBL Trex600ESP VX1e, Parkzone P51D, QRX350Pro
sutty is offline        Reply With Quote Quick reply to this message
Old 07-15-2012, 02:42 PM   #4 (permalink)
Registered Users
 
Posts: 370
Thread Starter Thread Starter
 

Join Date: Jan 2011
Location: Vancouver Canada
Default

To Sutty, no I don't think I have any problem in saving but just want to make sure since I am flying a 700 and try to be 100% sure for everything . I had seen many different opinion on this matter , I looked in the manual it didn't mention or the setups videos same thing. The more I read the forum the more I get worry , you know what I mean !! Regards.
__________________
Trex450Pro BeastX
Trex550E HC3SX
Trex700E HC3SX
JR11X
bladesr is offline        Reply With Quote Quick reply to this message
Old 07-15-2012, 03:04 PM   #5 (permalink)
Registered Users
 
Posts: 10,180
 
My HF Map location
Join Date: Feb 2008
Location: Manchester, England
Default

If you have some worry, and I can undersand that for a 700, then simply look at J. When you go into J, if it starts at 0 on the blades, and your servo arms are square, or where you need them to be, like you set-up at G, then you know you did everything right, because J uses the same starting position as saved at G, in other words the elctronically adjusted centres.

You can also triple check by putting your radio at mid stick, in throttle hold, or with motor disconnected, and see if you get the same there as well. It should be at least very close, depending on the calibration of your radio.

The more you read the more you worry, well stop reading then, lol. Kidding of course, but if you have done a lot of reading then you will be better placed to understand all the potential issues, so you should worry less.

Good luck with the maiden.

Cheers

Sutty
__________________
Regards, Sutty
BeltEXI, mCX, mSR, 4G3, FBL Trex250SE ÁB, FBL Trex450Pro ÁB,
FBL Trex550e VX1 Pro, FBL Trex600ESP VX1e, Parkzone P51D, QRX350Pro
sutty is offline        Reply With Quote Quick reply to this message
Old 07-15-2012, 03:50 PM   #6 (permalink)
Registered Users
 
Posts: 370
Thread Starter Thread Starter
 

Join Date: Jan 2011
Location: Vancouver Canada
Default

To Sutty ,
I think I did all the those steps you mentioned correctly It is for only the last part of the Step G I always thought each time I move a servo when in servo mode it is set at that position automatically , so I never think of when is the right position ( lights on / off) to leave Step G in order to save settings.

Regards
Anthony.
__________________
Trex450Pro BeastX
Trex550E HC3SX
Trex700E HC3SX
JR11X
bladesr is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
 

SEO by vBSEO 3.6.1