Register Now

onehot69stepside · 07-22-2009, 12:49 AM

my g10 order has been fulfilled and shipped finally. soon guys and gals

onehot69stepside · 07-23-2009, 07:11 PM

got the g10. This stuff is stout! pictures soon.

onehot69stepside · 11-27-2009, 02:54 AM

taken advantage of the much needed holiday weekend and got a frame assembled. Its super strong and each side is made into an i beam (or z beam) to eliminate flex.

onehot69stepside · 11-27-2009, 03:21 AM

im sorry guys... my computer wont recognize my digital camera. I tried my hardest to at least get some pics with my iphone. In the first picture you can see the braces from underneath that create the i beam effect and make the frame very stiff.

onehot69stepside · 11-27-2009, 12:59 PM

some more i wanted to add... the area directly behind the rear motor mount bolt where the frame edge has a corner and goes upward towards the upper shaft bearing block will have a nice large radius rather than the sharp corner there. This is where damyzx broke his cf frame in half from so much motor torque. the radius there will add a lot of strength.

just wanted to repost this drawing as it might help point out the braces in the dark pictures

damyxz · 12-02-2009, 11:14 PM

Hey, great job man, Is it possible for you to send me a frameset via USPS COD? I closed my paypal account because they screwed me over. I will test fly the frameset as soon as I get it. Hopefully before the Orlando event, so I can show it off. Thanks for making these. I also developed a passive power bus for the cyclic servos which isolated from the receiver. I have burnt out 2 AR 7000's because of too much amp draw from the cyclics and I have been successful with the design.

onehot69stepside · 12-12-2009, 01:53 PM

your lower frames and the braces are cut. Just a few mods to the design of the uppers and theyll be cut and headed your way.

damyxz · 12-28-2009, 10:47 PM

Thanks man, Just say when it is ready and I'll PM you.

07-22-2009, 12:49 AM	#121 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	my g10 order has been fulfilled and shipped finally. soon guys and gals __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

07-23-2009, 07:11 PM	#122 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	got the g10. This stuff is stout! pictures soon. __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

11-27-2009, 02:54 AM	#123 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	taken advantage of the much needed holiday weekend and got a frame assembled. Its super strong and each side is made into an i beam (or z beam) to eliminate flex. Attached Thumbnails __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

11-27-2009, 03:21 AM	#124 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	im sorry guys... my computer wont recognize my digital camera. I tried my hardest to at least get some pics with my iphone. In the first picture you can see the braces from underneath that create the i beam effect and make the frame very stiff. __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

11-27-2009, 12:59 PM	#125 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	some more i wanted to add... the area directly behind the rear motor mount bolt where the frame edge has a corner and goes upward towards the upper shaft bearing block will have a nice large radius rather than the sharp corner there. This is where damyzx broke his cf frame in half from so much motor torque. the radius there will add a lot of strength. just wanted to repost this drawing as it might help point out the braces in the dark pictures Attached Thumbnails __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

12-02-2009, 11:14 PM	#126 (permalink)
damyxz Registered Users My HF Map location Join Date: Jan 2007	Hey, great job man, Is it possible for you to send me a frameset via USPS COD? I closed my paypal account because they screwed me over. I will test fly the frameset as soon as I get it. Hopefully before the Orlando event, so I can show it off. Thanks for making these. I also developed a passive power bus for the cyclic servos which isolated from the receiver. I have burnt out 2 AR 7000's because of too much amp draw from the cyclics and I have been successful with the design. __________________ _____________________ Scott's Hobbies DVS inc.

12-12-2009, 01:53 PM	#127 (permalink)
onehot69stepside Registered Users Thread Starter Join Date: May 2008	your lower frames and the braces are cut. Just a few mods to the design of the uppers and theyll be cut and headed your way. __________________ MSR-X, Nano CPX, Belt CP Metal Edition w/g10 DTS align compatible frame, Trex 450 pro v2 w/metal upgrades, TREX 550e v2 w/ kde upgrades. CUSTOM CNC MACHINING... Inquire within.

12-28-2009, 10:47 PM	#128 (permalink)
damyxz Registered Users My HF Map location Join Date: Jan 2007	Thanks man, Just say when it is ready and I'll PM you. __________________ _____________________ Scott's Hobbies DVS inc.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in