CB 100 tail happy - HeliFreak
Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Walkera Helicopters > CB100


CB100 Walkera CB100 Helicopter Support


Reply
 
LinkBack Thread Tools Display Modes
Old 03-30-2012, 08:10 AM   #1 (permalink)
Registered Users
 

Join Date: Mar 2012
Location: Grand Rapids, MI USA
Default CB 100 tail happy

My CB 100 flies great until I put the canopy back on. Is it transmitting vibration to the gyro in the receiver? The receiver is held on with rubber bands and this may have bulked things up in the nose.
Phil
papu is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 04-12-2012, 04:05 PM   #2 (permalink)
Registered Users
 
Posts: 735
 

Join Date: Feb 2012
Location: NJ
Default

Hi, I have been fighting this issue for sometime now. I am not sure what reciever you have but my 1st cb100 has a 2436Rx and it was wire tied and sandwiched by the tail and main esc under the canopy. I read that on the 2436 does not like to be tied down so I did away with it. I switched my Rx to a 2605a and that fixed my problem till I had to replace the tail motor. You might want to check your tail blade they tend to loosen over time. put a dab of hot glue on it. That maybe all you need. hope this helps you out.
__________________
When you are lying on the floor there is no place to go but up!
Trex 480 Pro DFC, RoBird, Devo 10 Deviation 3.0,
Trex 450 Pro DFC, AR7200BX, Devo 10 Deviation 3.0
HeliIntervention is offline        Reply With Quote Quick reply to this message
Old 04-12-2012, 04:52 PM   #3 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Mar 2012
Location: Grand Rapids, MI USA
Default

It has a 2406b rx. I finally turned down the gyro gain, as I thought motor vibration was confusing the gyro, and this did help a lot. Debulking the nose (ie eliminting the rubber bands, and using two sided tape) also helped. Adjusting the AMS in the swash settings (found it in another thread) has eliminated most of the unwanted yaw with rapid vertical ascent and descent. Its back to being fun to fly again. The tail rotor is already glued to the shaft.
Phil
papu is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Insurance
Please select your insurance company (Optional)
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © VerticalScope Inc. All rights reserved.
 

SEO by vBSEO 3.6.1